id0917008011x1

Driver-side

1.Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)

2.Remove the following parts:

(1)Driver-side front scuff plate (See FRONT SCUFF PLATE REMOVAL/INSTALLATION.)

(2)Driver-side front side trim (See FRONT SIDE TRIM REMOVAL/INSTALLATION.)

(3)Driver-side decoration panel (See DECORATION PANEL REMOVAL/INSTALLATION.)

(4)Passenger-side decoration panel (See DECORATION PANEL REMOVAL/INSTALLATION.)

(5)Hood release lever (See HOOD RELEASE LEVER AND RELEASE CABLE REMOVAL/INSTALLATION [(US)].)

3.Partially peel back the seaming welt.

am3zzw00021944

4.Remove the bolt.

am3zzw00021945

5.Remove the screw.

6.Move the driver-side lower panel in the order of arrows (1), (2), (3) and (4) shown in the figure, and remove the clips, hook, tab, and guide.

am3zzw00029184

7.Disconnect the connectors.

am3zzw00021947

8.Remove the wiring harness clip.

9.Install in the reverse order of removal.

Note

• When replacing the driver-side lower panel, remove the cluster switch. (See CLUSTER SWITCH REMOVAL/INSTALLATION.)

Center

1.Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)

2.Remove the following parts:

(1)Shift lever knob (MTX) (See SHIFT LEVER REMOVAL/INSTALLATION [C66M-R].)

(2)Selector lever knob (ATX) (See SELECTOR LEVER COMPONENT REMOVAL/INSTALLATION.)

(3)Shift panel (See SHIFT PANEL REMOVAL/INSTALLATION.)

(4)Front console box (See FRONT CONSOLE BOX REMOVAL/INSTALLATION.)

(5)Cup holder (See CUP HOLDER REMOVAL/INSTALLATION.)

(6)Side wall (See SIDE WALL REMOVAL/INSTALLATION.)

(7)Rear console (See REAR CONSOLE REMOVAL/INSTALLATION [(US)].)

(8)Driver-side front scuff plate (See FRONT SCUFF PLATE REMOVAL/INSTALLATION.)

(9)Driver-side front side trim (See FRONT SIDE TRIM REMOVAL/INSTALLATION.)

(10)Driver-side decoration panel (See DECORATION PANEL REMOVAL/INSTALLATION.)

(11)Passenger-side decoration panel (See DECORATION PANEL REMOVAL/INSTALLATION.)

(12)Hood release lever (See HOOD RELEASE LEVER AND RELEASE CABLE REMOVAL/INSTALLATION [(US)].)

(13)Driver-side lower panel (See LOWER PANEL REMOVAL/INSTALLATION [(US)].)

(14)Driver-side knee air bag module (See KNEE AIR BAG MODULE REMOVAL/INSTALLATION [STANDARD DEPLOYMENT CONTROL SYSTEM – MEXICO SPEC.].) (See KNEE AIR BAG MODULE REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM – US/CANADA SPEC.].)

3.Remove the screws.

am3zzw00021948

4.Move the center lower panel in the order of arrows (1) and (2), and remove it while detaching the clips.

am3zzw00021949

5.Disconnect the push button start connector.

6.Install in the reverse order of removal.

Note

• When replacing the center lower panel, remove the push button start. (See PUSH BUTTON START REMOVAL/INSTALLATION.)

Passenger-side

Removal

1.Remove the following parts:

(1)Passenger-side front scuff plate (See FRONT SCUFF PLATE REMOVAL/INSTALLATION.)

(2)Passenger-side front side trim (See FRONT SIDE TRIM REMOVAL/INSTALLATION.)

(3)Passenger-side decoration panel (See DECORATION PANEL REMOVAL/INSTALLATION.)

(4)Glove compartment (without passenger-side knee air bag module) (See GLOVE COMPARTMENT REMOVAL/INSTALLATION.)

(5)Dashboard under cover (See DASHBOARD UNDER COVER REMOVAL/INSTALLATION.)

2.Partially peel back the seaming welt.

am3zzw00021950

3.Remove the bolts.

am3zzw00021951

4.Remove the screws.

5.Move the passenger-side lower panel in the order of arrows (1), (2), (3), and (4) shown in the figure, and remove it while detaching the clips, tab, hook, and guide.

am3zzw00021952

Installation

1.Install the clips, tab, hook, and guide while pressing the passenger-side lower panel in the order of arrows (1), (2), (3), and (4) shown in the figure.

am3zzw00029185

2.Assemble the passenger-side lower panel to the dashboard and tighten the bolts and screws temporarily.

am3zzw00021951

3.Install the glove compartment. (without passenger-side knee air bag module) (See GLOVE COMPARTMENT REMOVAL/INSTALLATION.)

4.Measure the gap between the glove compartment and the passenger-side lower panel and verify that the measured value is within the nominal value. (without passenger-side knee air bag module)

• If not within the nominal value, move the passenger-side lower panel and adjust the installation position. (without passenger-side knee air bag module)

am3zzw00021954

5.Remove the glove compartment. (without passenger-side knee air bag module) (See GLOVE COMPARTMENT REMOVAL/INSTALLATION.)

6.Tighten the bolts and screws completely.

am3zzw00024113

7.Install the following parts:

(1)Dashboard under cover (See DASHBOARD UNDER COVER REMOVAL/INSTALLATION.)

(2)Passenger-side decoration panel (See DECORATION PANEL REMOVAL/INSTALLATION.)

(3)Passenger-side front side trim (See FRONT SIDE TRIM REMOVAL/INSTALLATION.)

(4)Passenger-side front scuff plate (See FRONT SCUFF PLATE REMOVAL/INSTALLATION.)

(5)Glove compartment (without passenger-side knee air bag module) (See GLOVE COMPARTMENT REMOVAL/INSTALLATION.)

8.Install the seaming welt.

am3zzw00021950