DETERMINING SHORT BETWEEN CIRCUITS LOCATION (CAN-BUS No.6) [(US)]
DETERMINING SHORT BETWEEN CIRCUITS LOCATION (CAN-BUS No.6) [(US)]
SM2566466
id1002x1004000
-
Caution
-
• Perform the following malfunction diagnosis only when it is diagnosed with a short to ground by CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(US)].)
System Wiring Diagram
am3zzw00027525
|
Determination Procedure
-
Caution
-
• When disconnecting the connector, verify that there is no looseness, damage, deformation, corrosion, or poor connection of the connector terminals.• When inspecting the connector, touch it with a paper clip or similar thin pin without directly inserting a tester probe into the terminal.• Disconnect the negative battery cable before performing any work that requires handling of connectors.
|
Step |
Inspection |
Action |
|
|---|---|---|---|
|
1
|
INSPECT BODY CONTROL MODULE (BCM) FOR SHORT BETWEEN CIRCUITS
• Switch the ignition off.
• Disconnect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the connector 2 which has body control module (BCM) terminals 2A and 2C.
• Connect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2A and 2C (wiring harness side).
• Is the voltage at body control module (BCM) terminals 2A and 2C (wiring harness side) the same?
|
Yes
|
Go to the next step.
|
|
No
|
Replace the body control module (BCM) because there is a short between circuits in the body control module (BCM).
|
||
|
2
|
INSPECT CAN LINE BETWEEN CONNECTOR C-10 AND BODY CONTROL MODULE (BCM) FOR SHORT BETWEEN CIRCUITS
• Switch the ignition off.
• Disconnect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the connector C-10.
• Connect the connector 2 which has body control module (BCM) terminals 2A and 2C.
• Connect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2A and 2C.
• Is the voltage at body control module (BCM) terminals 2A and 2C the same?
|
Yes
|
Repair or replace the wiring harness between the body control module (BCM) and connector C-10 because the wiring harness is shorted between circuits.
|
|
No
|
Go to the next step.
|
||
|
3
|
INSPECT CAN LINE BETWEEN REAR SIDE RADAR SENSOR (LH) AND CONNECTOR C-10 FOR SHORT BETWEEN CIRCUITS
• Switch the ignition off.
• Disconnect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Inspect for continuity between rear side radar sensor (LH) terminals C and D.
• Is there continuity?
|
Yes
|
Go to the next step.
|
|
No
|
Go to Step 5.
|
||
|
4
|
INSPECT REAR SIDE RADAR SENSOR (LH) FOR SHORT BETWEEN CIRCUITS
• Disconnect the rear side radar sensor (LH) connector.
• Inspect for continuity between rear side radar sensor (LH) terminals C and D (wiring harness side).
• Is there continuity?
|
Yes
|
Repair or replace the wiring harness between the rear side radar sensor (LH) and connector C-10 because the wiring harness is shorted between circuits.
|
|
No
|
Replace the rear side radar sensor (LH) because there is a short between circuits in the rear side radar sensor (LH).
|
||
|
5
|
INSPECT CAN LINE BETWEEN FRONT RADAR SENSOR AND CONNECTOR C-10 FOR SHORT BETWEEN CIRCUITS
• Inspect for continuity between front radar sensor terminals E and C.
• Is there continuity?
|
Yes
|
Go to the next step.
|
|
No
|
Go to Step 7.
|
||
|
6
|
INSPECT FRONT RADAR SENSOR FOR SHORT BETWEEN CIRCUITS
• Disconnect the front radar sensor connector.
• Inspect for continuity between front radar sensor terminals E and C (wiring harness side).
• Is there continuity?
|
Yes
|
Repair or replace the wiring harness between the front radar sensor and connector C-10 because the wiring harness is shorted between circuits.
|
|
No
|
Replace the front radar sensor because there is a short between circuits in the front radar sensor.
|
||
|
7
|
INSPECT CAN LINE BETWEEN CONNECTOR C-06 AND CONNECTOR C-10 FOR SHORT BETWEEN CIRCUITS
• Switch the ignition off.
• Disconnect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the connector C-06.
• Connect the connector C-10.
• Connect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2A and 2C.
• Is the voltage at body control module (BCM) terminals 2A and 2C the same?
|
Yes
|
Repair or replace the wiring harness between connector C-06 and connector C-10 because the wiring harness is shorted between circuits.
|
|
No
|
Go to the next step.
|
||
|
8
|
INSPECT BODY CONTROL MODULE (BCM) FOR SHORT BETWEEN CIRCUITS
• Switch the ignition off.
• Disconnect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the connector 4 which has body control module (BCM) terminals 4N and 4M.
• Connect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2A and 2C.
• Is the voltage at body control module (BCM) terminals 2A and 2C the same?
|
Yes
|
Repair or replace the wiring harness between the body control module (BCM) and connector C-06 because the wiring harness is shorted between circuits.
|
|
No
|
Replace the body control module (BCM) because there is a short between circuits in the body control module (BCM).
|
||