Menu +
Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

DTC P2610:00 [PCM (SKYACTIV-G)]

DTC P2610:00 [PCM (SKYACTIV-G)]

SM2334456

id0102t4303800



Outline

System malfunction location

Malfunction in body control module (BCM)
Detection condition
• Malfunction detected in body control module (BCM).
Precondition
• Switch the ignition ON (engine on)
• The following DTCs are not detected:
― P0335:00 and P0365:00
Fail-safe
• The fast idle up correction for the drive-by-wire control is inhibited.
Possible cause
• Body control module (BCM) malfunction
• PCM malfunction
System wiring diagram
• Not applicable
Connector diagram
• Not applicable



Diagnostic Procedure

Step

Inspection

Results

Action
1
RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION
• Record the freeze frame data/snapshot data.

Note
• Recording can be facilitated using the screen capture function of the PC.
—
Go to the next step.
2
VERIFY RELATED REPAIR INFORMATION OR SERVICE INFORMATION AVAILABILITY
• Verify related Service Bulletins, on-line repair information, or Service Information availability.
• Is any related Information available?
Yes
Perform repair or diagnosis according to the available information.
• If the vehicle is not repaired, go to the next step.
No
Go to the next step.
3
VERIFY BODY CONTROL MODULE (BCM) DTC
• Perform the DTC inspection for the body control module (BCM). (See DTC INSPECTION.)
• Are any DTCs displayed?
Yes
Repair the malfunctioning location according to the applicable DTC troubleshooting.
(See DTC TABLE [BODY CONTROL MODULE (BCM) (US)].)
No
Go to the next step.
4
INSPECT BODY CONTROL MODULE (BCM) BACKUP VOLTAGE CIRCUIT
• Switch the ignition off.
• Remove the MAIN 200 A fuse, F27 25 A fuse and F50 15 A fuse.
• Inspect the MAIN 200 A fuse, F27 25 A fuse and F50 15 A fuse.
• Is there any malfunction?
Yes
Replace the malfunctioning fuse.
Switch the ignition ON (engine on) and wait for 10 s or more.
Switch the ignition off.
Go to repair completion verification.
No
Replace the body control module (BCM) and perform the repair completion verification.
(See BODY CONTROL MODULE (BCM) REMOVAL/INSTALLATION.)
Repair completion verification 1
VERIFY THAT VEHICLE IS REPAIRED
• Install/connect the part removed/disconnected during the troubleshooting procedure.

Note
• DTC P2610:00 can be cleared by performing the engine start and stop procedure.
• Start the engine.
• Stop the engine.
• Clear the DTC recorded in the memory. (See CLEARING DTC.)
• Replicate the vehicle conditions at the time the DTC was detected using the following procedure.
― Perform the KOER self test. (See DTC INSPECTION.)
• Perform the DTC inspection for the PCM. (See DTC INSPECTION.)
• Is the same Pending DTC present?
Yes
Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.
(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(US)].)
If the CAN communication is normal, perform the diagnosis from Step 1.
• If the malfunction recurs, replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))].) (See PCM REMOVAL/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))].)
No
Go to the next step.
Repair completion verification 2
VERIFY IF OTHER DTCs DISPLAYED
• Perform the DTC inspection. (See DTC INSPECTION.)
• Are any other DTCs displayed?
Yes
Repair the malfunctioning location according to the applicable DTC troubleshooting.
No
DTC troubleshooting completed.