Menu +
Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

DTC P117A:00 [PCM (SKYACTIV-G (US))]

DTC P117A:00 [PCM (SKYACTIV-G (US))]

SM2565538


id0102t43169u0



Outline

System malfunction location

Engine oil temperature is high

Detection condition
• Any one of the following conditions is met:
― With an engine coolant temperature of 88.5 °C {191 °F} or more while in 5th gear or lower, an engine speed of 6,100 rpm (SKYACTIV-G 2.0)/ 5,800 rpm (SKYACTIV-G 2.5) or more continues for 6 min.
― The estimated engine oil temperature exceeds 140 °C {284 °F} continues for 6 min. (With active air shutter)
Fail-safe
• Limits engine speed
Possible cause
• High engine speed condition continues
• Active air shutter close malfunction (With active air shutter)
• PCM malfunction
System wiring diagram
• Not applicable
Connector diagram
• Not applicable



Diagnostic Procedure

Step

Inspection

Results

Action

1
RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION
• Record the freeze frame data/snapshot data.

Note
• Recording can be facilitated using the screen capture function of the PC.
Go to the next step.
2
VERIFY RELATED REPAIR INFORMATION OR SERVICE INFORMATION AVAILABILITY
• Verify related Service Bulletins, on-line repair information, or Service Information availability.
• Is any related Information available?
Yes
Perform repair or diagnosis according to the available information.
• If the vehicle is not repaired, go to the next step.
No
Go to the next step.
3
INSPECT FOR OTHER RELATED DTCs
• Perform the DTC inspection for the PCM. (See DTC INSPECTION.)
• Are any of the following DTCs displayed?
― P0335:00
― P059F:00
― P05A0:00
― P05A3:00
― P05C0:00
― U0284:00
Yes
Repair the malfunctioning location according to the applicable DTC troubleshooting.
No
Go to the next step.
4
INSPECT VEHICLE CONDITION FOR EFFECT ON MALFUNCTION
• Verify how the customer drives the vehicle by asking the customer the following:
• Does the engine speed exceed 6,100 rpm (SKYACTIV-G 2.0)/ 5,800 rpm (SKYACTIV-G 2.5) for 6 min or more while driving in 5th gear or lower gear?
Yes
Explain to the customer that the vehicle is normal. (performs control to protect the engine due to continuous engine speed exceeding 6,100 rpm (SKYACTIV-G 2.0)/ 5,800 rpm (SKYACTIV-G 2.5) for 6 min or more while in 5th gear or lower gear)
If there is a concern with customer’s driving, provide the customer some pertinent advice (such as gear selection, how to use manual mode).
Go to repair completion verification.
No
Go to the next step.
Repair completion verification 1
VERIFY THAT VEHICLE IS REPAIRED
• Install/connect the part removed/disconnected during the troubleshooting procedure.
• Clear the DTC recorded in the memory. (See CLEARING DTC.)
• Replicate the vehicle conditions at the time the DTC was detected using the following procedure.
― Start the engine and warm it up completely.
― Drive the vehicle.
• Perform the DTC inspection for the PCM. (See DTC INSPECTION.)
• Is the same Pending DTC present?
Yes
Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.
If the CAN communication is normal, perform the diagnosis from Step 1.
No
Go to the next step.
Repair completion verification 2
VERIFY IF OTHER DTCs DISPLAYED
• Perform the DTC inspection. (See DTC INSPECTION.)
• Are any other DTCs displayed?
Yes
Repair the malfunctioning location according to the applicable DTC troubleshooting.
No
DTC troubleshooting completed.