Menu +
Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

DTC P05A0:00 [PCM (SKYACTIV-G)]

DTC P05A0:00 [PCM (SKYACTIV-G)]

SM2334478

id0102t4402200



Outline

System malfunction location

Active air shutter: Opening angle abnormality (sticking)
Detection condition
• Active air shutter opening angle is certain value or less while intake air temperature is 5 °C {41 °F} or more.
Fail-safe
• Performs fully open/closed position learning function three times.
Possible cause
• Foreign matter caught in active air shutter
• Active air shutter malfunction
• PCM malfunction
System wiring diagram
• Not applicable
Connector diagram
• Not applicable



Diagnostic Procedure

Step

Inspection

Results

Action
1
RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION
• Record the freeze frame data/snapshot data.

Note
• Recording can be facilitated using the screen capture function of the PC.
—
Go to the next step.
2
VERIFY RELATED REPAIR INFORMATION OR SERVICE INFORMATION AVAILABILITY
• Verify related Service Bulletins, on-line repair information, or Service Information availability.
• Is any related Information available?
Yes
Perform repair or diagnosis according to the available information.
• If the vehicle is not repaired, go to the next step.
No
Go to the next step.
3
INSPECT FOR OTHER RELATED DTCs
• Perform the DTC inspection for the PCM. (See DTC INSPECTION.)
• Are any of the following DTCs displayed?
― U0284:00
Yes
Repair the malfunctioning location according to the applicable DTC troubleshooting.
(See DTC U0284:00 [PCM (SKYACTIV-G)].)
No
Go to the next step.
4
VERIFY IF FOREIGN MATTER IS LODGED
• Verify if the active air shutter has lodged foreign matter.
• Has the active air shutter lodged any foreign matter?
Yes
Remove the foreign matter and perform the repair completion verification.
No
Go to the next step.
5
INSPECT ACTIVE AIR SHUTTER FOR MALFUNCTION
• Inspect the applicable part. (See ACTIVE AIR SHUTTER INSPECTION.)
• Is the part normal?
Yes
Go to the next step.
No
Repair or replace the malfunctioning location and perform the repair completion verification.
(See ACTIVE AIR SHUTTER REMOVAL/INSTALLATION.)
Repair completion verification 1
VERIFY THAT VEHICLE IS REPAIRED
• Install/connect the part removed/disconnected during the troubleshooting procedure.
• Clear the DTC recorded in the memory. (See CLEARING DTC.)
• Replicate the vehicle conditions at the time the DTC was detected using the following procedure.
― Start the engine.

Warning
• While performing this step, always operate the vehicle in a safe and lawful manner.
• When the M-MDS is used to observe monitor system status while driving, be sure to have another technician with you, or record the data in the M-MDS using the PID/DATA MONITOR AND RECORD capturing function and inspect later.
― Drive the vehicle at 10 km/h {6.2 mph} or more for approx. 1 min.
• Perform the DTC inspection for the PCM. (See DTC INSPECTION.)
• Is the same Pending DTC present?
Yes
Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.
(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(US)].)
If the CAN communication is normal, perform the diagnosis from Step 1.
• If the malfunction recurs, replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))].)
No
Go to the next step.
Repair completion verification 2
VERIFY IF OTHER DTCs DISPLAYED
• Perform the DTC inspection. (See DTC INSPECTION.)
• Are any other DTCs displayed?
Yes
Repair the malfunctioning location according to the applicable DTC troubleshooting.
No
DTC troubleshooting completed.