{"id":9983,"date":"2022-03-10T20:30:52","date_gmt":"2022-03-10T20:30:52","guid":{"rendered":"https:\/\/www.hexorcism.com\/19BP\/sm2565537\/"},"modified":"2022-03-10T20:30:52","modified_gmt":"2022-03-10T20:30:52","slug":"sm2565537","status":"publish","type":"page","link":"https:\/\/www.hexorcism.com\/19BP\/sm2565537\/","title":{"rendered":"DTC P013A:00 [PCM (SKYACTIV-G (US))]"},"content":{"rendered":"
\n

DTC P013A:00 [PCM (SKYACTIV-G (US))]<\/h3>\n<\/div>\n

SM2565537<\/p>\n

<\/p>\n
\n
\n
\n

id0102t43102u0<\/p>\n

\n
\n
Note<\/div>\n<\/dd>\n
\n
\u2022 To determine the malfunctioning part, proceed with the diagnostics from “Function Inspection Using M-MDS”.<\/div>\n<\/dd>\n<\/dl>\n



\n<\/a><\/p>\n

Details On DTCs<\/p>\n

\n\n\n\n\n\n\n\n\n\n\n\n\n
\n

Description<\/p>\n<\/th>\n

\n

HO2S: Slow response (during transition from rich to lean)<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
Detection condition<\/span><\/div>\n<\/td>\n
\n
Determination conditions<\/div>\n<\/td>\n
\n
\u2022 The response speed of the HO2S input signal when the air\/fuel ratio is fluctuated from rich to lean is slow.<\/div>\n<\/td>\n<\/tr>\n
\n
Preconditions<\/div>\n<\/td>\n
\n
\u2022 Fuel injection control: during fuel cut *1<\/sup><\/div>\n
\u2022 Catalytic converter estimated temperature: specified value or more<\/div>\n
\u2022 HO2S estimated temperature: specified value or more<\/div>\n
\u2022 HO2S output voltage during fuel cut: Specified value or more<\/div>\n
\u2022 The following DTCs are not detected:<\/div>\n
\n
\n
\u2015 HO2S heater: P0037:00 and P0038:00<\/div>\n
\u2015 MAF sensor: P0100:00, P0101:00 and U060F:00<\/div>\n
\u2015 ECT sensor No.1: P0117:00 and P0118:00<\/div>\n
\u2015 HO2S: P0137:00, P0138:00 and P0140:00<\/div>\n<\/dd>\n<\/dl>\n
*1<\/sup>: Standard can be verified by displaying PIDs using M-MDS<\/div>\n<\/td>\n<\/tr>\n
\n
Drive cycle<\/div>\n<\/td>\n
\n
\u2022 2<\/div>\n<\/td>\n<\/tr>\n
\n
Self test type<\/div>\n<\/td>\n
\n
\u2022 CMDTC self test<\/div>\n<\/td>\n<\/tr>\n
\n
Sensor used<\/div>\n<\/td>\n
\n
\u2022 HO2S<\/div>\n<\/td>\n<\/tr>\n
\n
Fail-safe function<\/span><\/div>\n<\/td>\n
\n
\u2022 Not applicable<\/div>\n<\/td>\n<\/tr>\n
\n
Vehicle status when DTCs are output<\/span><\/div>\n<\/td>\n
\n
\u2022 Not applicable<\/div>\n<\/td>\n<\/tr>\n
\n
Possible cause<\/span><\/div>\n<\/td>\n
\n
\u2022 HO2S malfunction<\/div>\n
\n
\n
\u2015 HO2S connector or terminals malfunction<\/div>\n
\u2015 HO2S incorrect installation<\/div>\n
\u2015 Exhaust system leakage<\/div>\n
\u2015 TWC damaged or malfunction<\/div>\n<\/dd>\n<\/dl>\n
\u2022 HO2S deterioration<\/div>\n
\u2022 HO2S heater malfunction<\/div>\n
\u2022 Improper operation of purge control system<\/div>\n
\n
\n
\u2015 Purge solenoid valve malfunction<\/div>\n
\u2015 Improper connection of evaporative hose (purge solenoid valve side)<\/div>\n<\/dd>\n<\/dl>\n
\u2022 Engine malfunction<\/div>\n
\n
\n
\u2015 Insufficient engine compression<\/div>\n<\/dd>\n<\/dl>\n
\u2022 PCM malfunction<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n



\n<\/a><\/p>\n

System Wiring Diagram<\/p>\n

\u2022 Not applicable<\/div>\n



\n<\/a><\/p>\n

Function Explanation (DTC Detection Outline)<\/p>\n

\u2022 If the rate at which the HO2S output voltage is lowered is slow during fuel cut, a DTC is stored.<\/div>\n



\n<\/a><\/p>\n

Repeatability Verification Procedure<\/p>\n

1. Warm up the engine to allow the engine coolant temperature to reach 80 \u00b0C {176 \u00b0F} or more<\/span>.<\/div>\n
2. Verify that OBD-II information (such as freeze frame data) has been obtained and recorded.<\/div>\n
3. Clear the DTC from the PCM memory using the M-MDS. (See CLEARING DTC<\/a>.)<\/div>\n
4. Switch the ignition off.<\/div>\n
5. Drive the vehicle for 15 min<\/span> at a speed of 40 km\/h {25 mph} or more<\/span>.<\/div>\n
6. Shift to 3rd gear and rapidly accelerate the vehicle to 60 km\/h {37 mph}<\/span>.<\/div>\n
7. Release the accelerator pedal and decelerate the vehicle to 40 km\/h {25 mph}<\/span>.<\/div>\n
8. Repeat Step 5 to 7 operations above 5 times<\/span>.<\/div>\n
9. Try to reproduce the malfunction by driving the vehicle for 5 min<\/span> based on the values in the freeze frame data\/snapshot data.<\/p>\n
\n
\n
Note<\/div>\n<\/dd>\n
\n
\u2022 Match the engine coolant temperature in the recorded freeze frame data\/snapshot data, the vehicle speed, and engine speed values to the best extent possible while driving the vehicle.<\/div>\n<\/dd>\n<\/dl>\n<\/div>\n



\n<\/a><\/p>\n

PID Item\/Simulation Item Used In Diagnosis<\/p>\n

\n

PID\/DATA monitor item table<\/p>\n\n\n\n\n\n
\n

PIDs<\/p>\n<\/th>\n

\n

Reference<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
HO2S_OUT_VOLT<\/div>\n<\/td>\n
\n
(See PID\/DATA MONITOR TABLE [PCM (SKYACTIV-G (US))]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n



\n<\/a><\/p>\n

Function Inspection Using M-MDS<\/p>\n

\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
\n

Step<\/p>\n<\/th>\n

\n

Inspection<\/p>\n<\/th>\n

\n

Results<\/p>\n<\/th>\n

\n

Action<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
1<\/div>\n<\/td>\n
\n
PURPOSE: VERIFY RELATED REPAIR INFORMATION OR SERVICE INFORMATION AVAILABILITY<\/div>\n
\u2022 Verify related Service Bulletins, on-line repair information, or Service Information availability.<\/div>\n
\u2022 Is any related Information available?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Perform repair or diagnosis according to the available information.<\/div>\n
\u2022 If the vehicle is not repaired, go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
2<\/div>\n<\/td>\n
\n
PURPOSE: RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION<\/div>\n
\u2022 Record the freeze frame data\/snapshot data and diagnostic monitoring test results (A\/F sensor, HO2S related).<\/p>\n
\n
\n
Note<\/div>\n<\/dd>\n
\n
\u2022 Recording can be facilitated using the screen capture function of the PC.<\/div>\n<\/dd>\n<\/dl>\n<\/div>\n<\/td>\n
\n
\u2014<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
3<\/div>\n<\/td>\n
\n
PURPOSE: VERIFY IF DIAGNOSTIC RESULT IS AFFECTED BY DTC RELATED TO A\/F SENSOR RESPONSIVENESS<\/div>\n
\u2022 Perform the DTC inspection for the PCM. (See DTC INSPECTION<\/a>.)<\/div>\n
\u2022 Are any of the following DTCs displayed?<\/div>\n
\n
\n
\u2015 P0133:00<\/div>\n<\/dd>\n<\/dl>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to Step 6.<\/div>\n<\/td>\n<\/tr>\n
\n
4<\/div>\n<\/td>\n
\n
PURPOSE: VERIFY IF DIAGNOSTIC RESULT IS AFFECTED BY DTC RELATED TO PURGE SOLENOID VALVE<\/div>\n
\u2022 Perform the DTC inspection for the PCM. (See DTC INSPECTION<\/a>.)<\/div>\n
\u2022 Are any of the following DTCs displayed?<\/div>\n
\n
\n
\u2015 P0443:00<\/div>\n<\/dd>\n<\/dl>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair the malfunctioning location according to the applicable DTC troubleshooting.<\/div>\n
(See DTC P0443:00 [PCM (SKYACTIV-G)]<\/a>.)<\/div>\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
5<\/div>\n<\/td>\n
\n
PURPOSE: VERIFY IF DIAGNOSTIC RESULT IS AFFECTED BY DTC OCCURRING FROM FUEL SYSTEM RELATED PART<\/div>\n
\u2022 Perform the DTC inspection for the PCM. (See DTC INSPECTION<\/a>.)<\/div>\n
\u2022 Are any other DTCs displayed?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair the malfunctioning location according to the applicable DTC troubleshooting.<\/div>\n
(See DTC TABLE [PCM (SKYACTIV-G (US))]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
A factor other than the HO2S can be considered the cause of the malfunction.<\/div>\n
\u2022 Go to Troubleshooting Diagnostic Procedure to perform the procedure from Step 1.<\/div>\n<\/td>\n<\/tr>\n
\n
6<\/div>\n<\/td>\n
\n
PURPOSE: VERIFY FLUCTUATION OF HO2S INPUT SIGNAL AT START OF FUEL CUT<\/div>\n
\u2022 Start the engine and warm it up completely.<\/div>\n
\u2022 Access the HO2S_OUT_VOLT PID using the M-MDS. (See PID\/DATA MONITOR INSPECTION<\/a>.)<\/div>\n
\u2022 Drive the vehicle under the following conditions.<\/p>\n
\n
\n
Warning<\/div>\n<\/dd>\n
\n
\n
\u2022 When the M-MDS is used to observe monitor system status while driving, be sure to have another technician with you, or record the data in the M-MDS using the PID\/DATA MONITOR AND RECORD capturing function and inspect later.<\/div>\n
\u2022 While performing this step, always operate the vehicle in a safe and lawful manner.<\/div>\n<\/div>\n<\/dd>\n<\/dl>\n<\/div>\n
\n
\n
\u2015 After increasing the engine speed to 4,000 rpm<\/span>, decelerate using engine braking.<\/div>\n<\/dd>\n<\/dl>\n
\u2022 Can a fluctuation in the displayed PID value be verified?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to Troubleshooting Diagnostic Procedure to perform the repair completion verification.<\/div>\n
\u2022 If a malfunction occurs, perform diagnosis from Step 1 of the malfunction diagnostic procedure.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
HO2S signal can be considered the cause.<\/div>\n
\u2022 Go to Troubleshooting Diagnostic Procedure to perform the procedure from Step 4.<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n



\n<\/a><\/p>\n

Troubleshooting Diagnostic Procedure<\/p>\n

Intention of troubleshooting procedure<\/div>\n
\u2022 Step 1\u20142<\/div>\n
\n
\n
\u2015 Perform an emission system parts inspection.<\/div>\n<\/dd>\n<\/dl>\n
\u2022 Step 3<\/div>\n
\n
\n
\u2015 Perform an engine inspection.<\/div>\n<\/dd>\n<\/dl>\n
\u2022 Step 4\u20149<\/div>\n
\n
\n
\u2015 Perform inspection of HO2S signal related parts.<\/div>\n<\/dd>\n<\/dl>\n
\u2022 Repair completion verification<\/div>\n
\n
\n
\u2015 Verify that the primary malfunction is resolved and there are no other malfunctions.<\/div>\n<\/dd>\n<\/dl>\n

\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
\n

Step<\/p>\n<\/th>\n

\n

Inspection<\/p>\n<\/th>\n

\n

Results<\/p>\n<\/th>\n

\n

Action<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
1<\/div>\n<\/td>\n
\n
PURPOSE: INSPECT PURGE SOLENOID VALVE FOR MALFUNCTION<\/div>\n
\u2022 Inspect the applicable part. (See PURGE SOLENOID VALVE INSPECTION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.) (See PURGE SOLENOID VALVE INSPECTION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
\u2022 Is the part normal?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Repair or replace the malfunctioning location and perform the repair completion verification.<\/div>\n
(See PURGE SOLENOID VALVE REMOVAL\/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
(See PURGE SOLENOID VALVE REMOVAL\/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
2<\/div>\n<\/td>\n
\n
PURPOSE: VERIFY IF DIAGNOSTIC RESULT IS AFFECTED BY MALFUNCTION RELATED TO POOR EVAPORATIVE HOSE CONNECTION<\/div>\n
\u2022 Verify the connection condition of the evaporative hose (purge solenoid valve side). (See PURGE SOLENOID VALVE REMOVAL\/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.) (See PURGE SOLENOID VALVE REMOVAL\/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
\u2022 Is the evaporative hose (purge solenoid valve side) connection normal?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Connect evaporative hose correctly and perform the repair completion verification.<\/div>\n
(See PURGE SOLENOID VALVE REMOVAL\/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
(See PURGE SOLENOID VALVE REMOVAL\/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
3<\/div>\n<\/td>\n
\n
PURPOSE: VERIFY IF MALFUNCTION RELATED TO ENGINE COMPRESSION AFFECTS DIAGNOSTIC RESULTS<\/div>\n
\u2022 Inspect the engine compression. (See COMPRESSION INSPECTION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.) (See COMPRESSION INSPECTION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
\u2022 Are compression pressures within specification?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Replace or overhaul the engine and perform the repair completion verification.<\/div>\n<\/td>\n<\/tr>\n
\n
4<\/div>\n<\/td>\n
\n
PURPOSE: INSPECT HO2S CONNECTOR FOR MALFUNCTION<\/div>\n
\u2022 Inspect the applicable connector and terminal. (See CONNECTOR INSPECTION<\/a>.)<\/div>\n
\u2022 Are the connector and terminal normal?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Repair or replace the malfunctioning location and perform the repair completion verification.<\/div>\n<\/td>\n<\/tr>\n
\n
5<\/div>\n<\/td>\n
\n
PURPOSE: VERIFY IF HO2S IS INSTALLED CORRECTLY<\/div>\n
\u2022 Verify the HO2S installation condition. (See HEATED OXYGEN SENSOR (HO2S) REMOVAL\/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.) (See HEATED OXYGEN SENSOR (HO2S) REMOVAL\/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
\u2022 Is the installation condition normal?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Correctly install the HO2S and perform the repair completion verification.<\/div>\n
(See HEATED OXYGEN SENSOR (HO2S) REMOVAL\/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
(See HEATED OXYGEN SENSOR (HO2S) REMOVAL\/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
6<\/div>\n<\/td>\n
\n
PURPOSE: INSPECT HO2S FOR MALFUNCTION<\/div>\n
\u2022 Inspect the applicable part. (See HEATED OXYGEN SENSOR (HO2S) INSPECTION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.) (See HEATED OXYGEN SENSOR (HO2S) INSPECTION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
\u2022 Is the part normal?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Repair or replace the malfunctioning location and perform the repair completion verification.<\/div>\n
(See HEATED OXYGEN SENSOR (HO2S) REMOVAL\/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
(See HEATED OXYGEN SENSOR (HO2S) REMOVAL\/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
7<\/div>\n<\/td>\n
\n
PURPOSE: INSPECT HO2S HEATER FOR MALFUNCTION<\/div>\n
\u2022 Inspect the applicable part. (See HEATED OXYGEN SENSOR (HO2S) INSPECTION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.) (See HEATED OXYGEN SENSOR (HO2S) INSPECTION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
\u2022 Is the part normal?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Repair or replace the malfunctioning location and perform the repair completion verification.<\/div>\n
(See HEATED OXYGEN SENSOR (HO2S) REMOVAL\/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
(See HEATED OXYGEN SENSOR (HO2S) REMOVAL\/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
8<\/div>\n<\/td>\n
\n
PURPOSE: INSPECT EXHAUST SYSTEM FOR LEAKAGE<\/div>\n
\u2022 Visually inspect for exhaust gas leakage from the exhaust system.<\/div>\n
\u2022 Is there any malfunction?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair or replace the malfunctioning location and perform the repair completion verification.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
9<\/div>\n<\/td>\n
\n
PURPOSE: VERIFY IF CATALYTIC CONVERTER DAMAGE AFFECTS HO2S SIGNAL<\/div>\n
\u2022 Verify if the catalytic converter is damaged.<\/div>\n
\u2022 Is there any malfunction?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair or replace the malfunctioning location and perform the repair completion verification.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Replace the HO2S and perform the repair completion verification.<\/div>\n
(See HEATED OXYGEN SENSOR (HO2S) REMOVAL\/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
(See HEATED OXYGEN SENSOR (HO2S) REMOVAL\/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
Repair completion verification 1<\/div>\n<\/td>\n
\n
PURPOSE: VERIFY THAT VEHICLE IS REPAIRED<\/div>\n
\u2022 Install\/connect the part removed\/disconnected during the troubleshooting procedure.<\/div>\n
\u2022 Clear the DTC recorded in the memory. (See CLEARING DTC<\/a>.)<\/div>\n
\u2022 Replicate the vehicle conditions at the time the DTC was detected using the following procedure.<\/div>\n
\n
\n
\u2015 Implement the repeatability verification procedure. (See Repeatability Verification Procedure<\/a>.)<\/div>\n<\/dd>\n<\/dl>\n
\u2022 Perform the DTC inspection for the PCM. (See DTC INSPECTION<\/a>.)<\/div>\n
\u2022 Is the same Pending DTC present?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.<\/div>\n
(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(US)]<\/a>.)<\/div>\n
If the CAN communication is normal, perform the diagnosis from Step 1.<\/div>\n
\u2022 If the malfunction recurs, replace the PCM, then go to the next step. (See PCM REMOVAL\/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.) (See PCM REMOVAL\/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
Repair completion verification 2<\/div>\n<\/td>\n
\n
PURPOSE: VERIFY IF OTHER DTCs DISPLAYED<\/div>\n
\u2022 Perform the DTC inspection. (See DTC INSPECTION<\/a>.)<\/div>\n
\u2022 Are any other DTCs displayed?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair the malfunctioning location according to the applicable DTC troubleshooting.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
DTC troubleshooting completed.<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n
<\/div>\n
<\/div>\n
<\/div>\n

<\/div>\n<\/div>\n","protected":false},"excerpt":{"rendered":"

DTC P013A:00 [PCM (SKYACTIV-G (US))] SM2565537 id0102t43102u0 Note \u2022 To determine the malfunctioning part, proceed with the diagnostics from “Function Inspection Using M-MDS”. Details On DTCs Description HO2S: Slow response (during transition from rich to lean) Detection condition Determination conditions \u2022 The response speed of the HO2S input signal when the air\/fuel ratio is fluctuated from rich to lean is slow. Preconditions \u2022 Fuel injection control: during fuel cut *1 \u2022 Catalytic converter estimated temperature: […]<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_monsterinsights_skip_tracking":false,"_monsterinsights_sitenote_active":false,"_monsterinsights_sitenote_note":"","_monsterinsights_sitenote_category":0,"footnotes":""},"class_list":["post-9983","page","type-page","status-publish","hentry"],"_links":{"self":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages\/9983","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/comments?post=9983"}],"version-history":[{"count":0,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages\/9983\/revisions"}],"wp:attachment":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/media?parent=9983"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}