{"id":9670,"date":"2022-03-10T20:30:49","date_gmt":"2022-03-10T20:30:49","guid":{"rendered":"https:\/\/www.hexorcism.com\/19BP\/sm2337302\/"},"modified":"2022-03-10T20:30:49","modified_gmt":"2022-03-10T20:30:49","slug":"sm2337302","status":"publish","type":"page","link":"https:\/\/www.hexorcism.com\/19BP\/sm2337302\/","title":{"rendered":"IMAGE NOT OUTPUT IN ALL MODES"},"content":{"rendered":"
\n

IMAGE NOT OUTPUT IN ALL MODES<\/h3>\n<\/div>\n

SM2337302<\/p>\n

<\/p>\n
\n
\n
\n

id160300000200<\/p>\n



\n<\/a><\/p>\n

Outline<\/p>\n

\n\n\n\n\n\n
\n
Possible cause<\/div>\n<\/td>\n
\n
\u2022 Connector or terminal malfunction of the following parts:<\/div>\n
\n
\n
\u2015 Center display<\/div>\n
\u2015 Connectivity master unit (CMU)<\/div>\n<\/dd>\n<\/dl>\n
\u2022 Short to ground or open circuit in center display power supply circuit<\/div>\n
\u2022 Center display malfunction<\/div>\n
\u2022 Connectivity master unit (CMU) malfunction<\/div>\n<\/td>\n<\/tr>\n
<\/td>\n<\/tr>\n
<\/td>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n



\n<\/a><\/p>\n

Diagnostic Procedure<\/p>\n

\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
\n

Step<\/p>\n<\/th>\n

\n

Inspection<\/p>\n<\/th>\n

\n

Results<\/p>\n<\/th>\n

\n

Action<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
1<\/div>\n<\/td>\n
\n
VERIFY ALL SYSTEM DTCs<\/div>\n
\u2022 Perform the DTC inspection. (Refer to the [DTC INSPECTION] in the workshop manual)<\/div>\n
\u2022 Are any DTCs displayed?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair the malfunctioning location according to the applicable DTC troubleshooting.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
2<\/div>\n<\/td>\n
\n
INSPECT CENTER DISPLAY AND CONNECTIVITY MASTER UNIT (CMU) CONNECTORS FOR MALFUNCTION<\/div>\n
\u2022 Inspect the applicable connector and terminal. (Refer to the [CONNECTOR INSPECTION] in the workshop manual)<\/div>\n
\u2022 Are the connector and terminal normal?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Repair or replace the malfunctioning location and perform the repair completion verification.<\/div>\n<\/td>\n<\/tr>\n
\n
3<\/div>\n<\/td>\n
\n
INSPECT CENTER DISPLAY POWER SUPPLY CIRCUIT FOR SHORT TO GROUND AND OPEN CIRCUIT<\/div>\n
\u2022 Inspect the power supply circuit for a short to ground and open circuit. (Refer to the [CIRCUIT INSPECTION] in the workshop manual)<\/div>\n
\u2022 Is the circuit normal?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Repair or replace the malfunctioning location and perform the repair completion verification.<\/div>\n<\/td>\n<\/tr>\n
\n
4<\/div>\n<\/td>\n
\n
INSPECT CENTER DISPLAY FOR MALFUNCTION<\/div>\n
\u2022 Perform diagnostic assist function \u201cFunctional Inspection\/Adjustment\u201d display test. (See DIAGNOSTIC ASSIST FUNCTION [CONNECTIVITY MASTER UNIT (US)]<\/a>.)<\/div>\n
\u2022 Is the part normal?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Repair or replace the malfunctioning location and perform the repair completion verification.<\/div>\n
(Refer to the [CENTER DISPLAY REMOVAL\/INSTALLATION] in the workshop manual)<\/div>\n<\/td>\n<\/tr>\n
\n
Repair completion verification<\/div>\n<\/td>\n
\n
VERIFY THAT VEHICLE IS REPAIRED<\/div>\n
\u2022 Install\/connect the part removed\/disconnected during the troubleshooting procedure.<\/div>\n
\u2022 Has the malfunction symptom been eliminated?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Complete the symptom troubleshooting. (Explain contents of repair to customer)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.<\/div>\n
(Refer to the [CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW] in the workshop manual)<\/div>\n
If the CAN communication is normal, perform the diagnosis from Step 1.<\/div>\n
\u2022 If the malfunction is not resolved, replace the connectivity master unit (CMU). (Refer to the [CONNECTIVITY MASTER UNIT (CMU) REMOVAL\/INSTALLATION] in the workshop manual)<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n
<\/div>\n
<\/div>\n
<\/div>\n

<\/div>\n<\/div>\n","protected":false},"excerpt":{"rendered":"

IMAGE NOT OUTPUT IN ALL MODES SM2337302 id160300000200 Outline Possible cause \u2022 Connector or terminal malfunction of the following parts: \u2015 Center display \u2015 Connectivity master unit (CMU) \u2022 Short to ground or open circuit in center display power supply circuit \u2022 Center display malfunction \u2022 Connectivity master unit (CMU) malfunction Diagnostic Procedure Step Inspection Results Action 1 VERIFY ALL SYSTEM DTCs \u2022 Perform the DTC inspection. (Refer to the [DTC INSPECTION] in the workshop […]<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_monsterinsights_skip_tracking":false,"_monsterinsights_sitenote_active":false,"_monsterinsights_sitenote_note":"","_monsterinsights_sitenote_category":0,"footnotes":""},"class_list":["post-9670","page","type-page","status-publish","hentry"],"_links":{"self":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages\/9670","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/comments?post=9670"}],"version-history":[{"count":0,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages\/9670\/revisions"}],"wp:attachment":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/media?parent=9670"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}