{"id":9645,"date":"2022-03-10T20:30:49","date_gmt":"2022-03-10T20:30:49","guid":{"rendered":"https:\/\/www.hexorcism.com\/19BP\/sm2337173\/"},"modified":"2022-03-10T20:30:49","modified_gmt":"2022-03-10T20:30:49","slug":"sm2337173","status":"publish","type":"page","link":"https:\/\/www.hexorcism.com\/19BP\/sm2337173\/","title":{"rendered":"360\u00b0VIEW MONITOR SYSTEM AIMING"},"content":{"rendered":"
\n

360\u00b0VIEW MONITOR SYSTEM AIMING<\/h3>\n<\/div>\n

SM2337173<\/p>\n

<\/p>\n
\n
\n
\n

id152000010200<\/p>\n

\n

Special service tool (SST)<\/p>\n\n\n\n
\n
49 L067 006<\/div>\n
<\/div>\n
Plumb bob<\/div>\n<\/td>\n
<\/td>\n\n
49 JP04 001<\/div>\n
<\/div>\n
Target marker<\/div>\n<\/td>\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n



\n<\/a><\/p>\n

Preparation Before Servicing<\/p>\n

1.Empty the vehicle by having all occupants leave the vehicle and remove all the cargo except for the spare tire, jack and tools equipped on the vehicle.<\/p>\n

\n

2.Adjust the air pressure of each tire to the specified value. (See WHEEL AND TIRE SPECIFICATION [(US)]<\/a>.)<\/p>\n

\n

3.Move the vehicle to level ground.<\/p>\n

\n

\n
\n
Caution<\/div>\n<\/dd>\n
\n
\n
\u2022 If the setting surface height and angle between the vehicle and the target marker differs, correct front camera aiming cannot be done. Perform the front camera aiming with the vehicle and target marker setting surface on level ground.<\/div>\n
\u2022 Level ground conditions must be within 2 degrees for the front and back, and right and left.<\/div>\n
\u2022 Do not move or shake the vehicle during aiming adjustment (such as riding in or opening a door).<\/div>\n
\u2022 Remove dust or dirt from the lens surface of the 4 cameras.<\/div>\n
\u2022 The voltage supplied to the 360\u00b0 view monitor control module must be 9.5\u201415.5 V<\/span>.<\/div>\n
\u2022 The aiming adjustment must be performed under approx. -30\u201460 \u00b0C {-22\u2014140 \u00b0F}<\/span> conditions.<\/div>\n\n\n\n
\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00036900<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/dd>\n<\/dl>\n

4.Using the M-MDS, perform a DTC inspection for 360\u00b0 view monitor unit and verify that no DTCs are displayed. (See DTC INSPECTION<\/a>.)<\/p>\n

\n

\n
\n
Note<\/div>\n<\/dd>\n
\n
\u2022 If any DTCs are displayed, perform malfunction repair referring to the applicable DTC troubleshooting. (See DTC TABLE [360\u00b0VIEW MONITOR CONTROL MODULE (US)]<\/a>.) (See DTC TABLE [VEHICLE CONTROL MODULE (US)]<\/a>.)<\/div>\n<\/dd>\n<\/dl>\n

5.Adjust the SST<\/span> so that it is aligned with the center of the brand emblem, determine the center position at the front of the vehicle, and mark the center position (point A) on the floor surface.<\/p>\n

\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00036901<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
\n
\n
Note<\/div>\n<\/dd>\n
\n
\u2022 The center of the brand emblem indicates the center position of the vehicle.<\/div>\n<\/dd>\n<\/dl>\n

6.Adjust the SST<\/span> so that it is aligned with the center of the brand emblem, determine the center position at the rear of the vehicle, and mark the center position (point B) on the floor surface.<\/p>\n

\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00036902<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
\n
\n
Note<\/div>\n<\/dd>\n
\n
\u2022 The center of the brand emblem indicates the center position of the vehicle.<\/div>\n<\/dd>\n<\/dl>\n

7.Pull the leveling line towards the front and rear of the vehicle and adjust it so that it passes over points A and B.<\/p>\n

\n

\n
\n
Note<\/div>\n<\/dd>\n
\n
\u2022 Use a commercially-available leveling line.<\/div>\n<\/dd>\n<\/dl>\n\n\n\n
\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00036903<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

8.Secure the leveling line.<\/p>\n

\n



\n<\/a><\/p>\n

Selection of Procedure for 360\u00b0 View Monitor System Aiming<\/p>\n

\n
\n
Note<\/div>\n<\/dd>\n
\n
\n
\u2022 For the front camera aiming, side camera aiming, and rear mount camera aiming, 1 set(1 set\/2 targets) of the SST (49 JP04 001)<\/span> are required.<\/div>\n
\u2022 For the 360\u00b0 view monitor system aiming (batch aiming), 4 sets(1 set\/2 targets) of the SST (49 JP04 001)<\/span> are required. If 4 sets of the SST (49 JP04 001)<\/span> is unavailable, perform the aiming for the 4 cameras individually.<\/div>\n
\u2022 When any of the following operations is performed, it is necessary to verify if the front camera aiming, side camera aiming, and rear mount camera aiming needs to be performed.<\/div>\n
\n
\n
\u2015 Servicing requiring verification of necessity to perform front camera aiming<\/div>\n
\n
\n
\u2022 Front camera removal\/installation<\/div>\n
\u2022 Front bumper removal\/installation<\/div>\n<\/dd>\n<\/dl>\n<\/dd>\n<\/dl>\n
\n
\n
\u2015 Servicing requiring verification of necessity to perform side camera aiming<\/div>\n
\n
\n
\u2022 Side camera removal\/installation<\/div>\n
\u2022 Power outer mirror removal\/installation<\/div>\n
\u2022 Lower outer mirror garnish removal\/installation<\/div>\n
\u2022 Side turn light removal\/installation<\/div>\n
\u2022 Front door removal\/installation or adjustment<\/div>\n<\/dd>\n<\/dl>\n<\/dd>\n<\/dl>\n
\n
\n
\u2015 Servicing requiring verification of necessity to perform rear mount camera aiming<\/div>\n
\n
\n
\u2022 Rear mount camera removal\/installation<\/div>\n
\u2022 Rear bumper removal\/installation<\/div>\n<\/dd>\n<\/dl>\n<\/dd>\n<\/dl>\n<\/div>\n<\/dd>\n<\/dl>\n

\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
\n

Step<\/p>\n<\/th>\n

\n

Procedure<\/p>\n<\/th>\n

\n

Action after procedure<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
1<\/div>\n<\/td>\n
\n
Was the 360\u00b0 view monitor control module replaced?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to step 4.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
2<\/div>\n<\/td>\n
\n
To determine if aiming is necessary or not, perform the 360\u00b0 view monitor system screen display verification procedure.<\/div>\n
(See 360\u00b0 View Monitor System Screen Display Verification Procedure<\/a>)<\/div>\n
Is it necessary to perform aiming?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Procedure is completed.<\/div>\n<\/td>\n<\/tr>\n
\n
3<\/div>\n<\/td>\n
\n
Which of the cameras requires aiming?<\/div>\n<\/td>\n
\n
Front camera<\/div>\n<\/td>\n
\n
Perform the front camera aiming and go to step 5.<\/div>\n
(See Front Camera Aiming Procedure<\/a>)<\/div>\n<\/td>\n<\/tr>\n
\n
Side camera<\/div>\n<\/td>\n
\n
Perform the side camera aiming and go to step 5.<\/div>\n
(See Side Camera Aiming Procedure<\/a>)<\/div>\n<\/td>\n<\/tr>\n
\n
Rear mount camera<\/div>\n<\/td>\n
\n
Perform the rear mount camera aiming and go to step 5.<\/div>\n
(See Rear Mount Camera Aiming Procedure<\/a>)<\/div>\n<\/td>\n<\/tr>\n
\n
4<\/div>\n<\/td>\n
\n
For the 360\u00b0 view monitor system aiming (batch aiming), 4 sets of the SST (49 JP04 001)<\/span> are required.<\/div>\n
Are 4 sets of the SST (49 JP04 001)<\/span> available?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Perform the 360\u00b0 view monitor system aiming (batch aiming) procedure and go to step 5.<\/div>\n
(See 360\u00b0 View Monitor System Aiming (Batch Aiming) Procedure<\/a>)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Individually perform aiming for the camera requiring aiming, then go to Step 5.<\/div>\n
(See Front Camera Aiming Procedure<\/a>)<\/div>\n
(See Side Camera Aiming Procedure<\/a>)<\/div>\n
(See Rear Mount Camera Aiming Procedure<\/a>)<\/div>\n<\/td>\n<\/tr>\n
\n
5<\/div>\n<\/td>\n
\n
Perform the 360\u00b0 view monitor system screen display verification procedure.<\/div>\n
(See 360\u00b0 View Monitor System Screen Display Verification Procedure<\/a>)<\/div>\n
Is 360\u00b0 view monitor system aiming procedure needed?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repeat Step 4.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Procedure is completed.<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n



\n<\/a><\/p>\n

360\u00b0 View Monitor System Screen Display Verification Procedure<\/p>\n

1.Perform the preparation before servicing. (See Preparation Before Servicing<\/a>.)<\/p>\n

\n

2.Position the white lines at the positions shown in the figure.<\/p>\n

\n

If all the cameras are verified<\/p>\n\n\n\n
\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00036904<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

If the front camera is verified<\/p>\n\n\n\n
\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00036905<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

If the side camera is verified<\/p>\n\n\n\n
\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00036906<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

If the rear mount camera is verified<\/p>\n\n\n\n
\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00036907<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
\n
\n
Note<\/div>\n<\/dd>\n
\n
\u2022 Use paper of 10 mm {0.39 in}<\/span> thickness or less, or tape for the white lines.<\/div>\n<\/dd>\n<\/dl>\n

3.Close all the doors (front door, rear door) and the trunk lid (4SD)\/liftgate (5HB).<\/p>\n

\n

4.Verify that the outer mirrors are unfolded.<\/p>\n

\n

5.Operate the electric parking brake.<\/p>\n

\n

6.Shift the selector lever to the P position. (ATX)<\/p>\n

\n

7.Shift the shift lever to the neutral position. (MTX)<\/p>\n

\n

8.Switch the ignition ON (engine off or on).<\/p>\n

\n

9.Display the screen of the 360\u00b0 view monitor system in the center display by pressing the 360\u00b0 view monitor switch.<\/p>\n

\n

\n
\n
Note<\/div>\n<\/dd>\n
\n
\n
\u2022 If the projected vehicle path indication (yellow line) obscures the white lines, uncheck the check mark in the guide line display setting to turn the projected vehicle path indication off.<\/div>\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00036908<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/dd>\n<\/dl>\n

10.Verify that there are no breaks in the seams of the white lines in the display screen of the center display.<\/p>\n

\n

\n
\n
\u2022 If there are no breaks in the seams of the white lines, the 360\u00b0 view monitor system aiming is completed.<\/div>\n
\u2022 If there are breaks in the seams of the white lines, perform the aiming procedure. (See 360\u00b0 View Monitor System Aiming (Batch Aiming) Procedure<\/a>.)<\/div>\n
\u2022 If the white lines cannot be found, a position has deviated, or the seams of the white lines lean largely to one side, return to Step 2 and verify the white line position.<\/div>\n<\/dd>\n<\/dl>\n\n\n\n
\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
ac8wzw00000988<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n



\n<\/a><\/p>\n

360\u00b0 View Monitor System Aiming (Batch Aiming) Procedure<\/p>\n

1.Position the SSTs<\/span> at the positions shown in the figure.<\/p>\n

\n\n\n\n
\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00036909<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

2.Connect the M-MDS to the DLC-2.<\/p>\n

\n

3.Close all the doors (front door, rear door) and the trunk lid (4SD)\/liftgate (5HB).<\/p>\n

\n

4.Verify that the outer mirrors are unfolded.<\/p>\n

\n

5.Operate the electric parking brake.<\/p>\n

\n

6.Shift the selector lever to the P position. (ATX)<\/p>\n

\n

7.Shift the shift lever to the neutral position. (MTX)<\/p>\n

\n

8.After vehicle identification is completed, select the following from the M-MDS initial screen.<\/p>\n

\n

\n
(1)[Toolbox]<\/dd>\n
<\/dd>\n<\/dl>\n
\n
(2)[Work Support]<\/dd>\n
<\/dd>\n<\/dl>\n
\n
(3)[i-ACTIVSENSE]<\/dd>\n
<\/dd>\n<\/dl>\n
\n
(4)[Static aiming]<\/dd>\n
<\/dd>\n<\/dl>\n
\n
(5)[Static aiming for 360\u00b0 View Monitor System]<\/dd>\n
<\/dd>\n<\/dl>\n

9.Perform the 360\u00b0 view monitor system aiming according to the directions on the M-MDS.<\/p>\n

\n

10.Verify the M-MDS display.<\/p>\n

\n

\n
\n
\u2022 If [Procedure completed successfully] is displayed<\/div>\n
\n
\n
\u2015 The 360\u00b0 view monitor system aiming is completed. Perform the 360\u00b0 view monitor system screen display verification procedure. (See 360\u00b0 View Monitor System Screen Display Verification Procedure<\/a>.)<\/div>\n<\/dd>\n<\/dl>\n<\/dd>\n<\/dl>\n
\n
\n
\u2022 If [Procedure not completed successfully] is displayed.<\/div>\n
\n
\n
\u2015 Perform an inspection according to the following table for the error code procedure.<\/div>\n
\u2015 If an error code other than the error codes in the following table is displayed, verify the following and perform the 360\u00b0 view monitor system aiming again if there is no malfunction, as there could be a communication error between the 360\u00b0 view monitor unit and the diagnostic tester.<\/div>\n
\n
\n
1. Is the battery positive voltage for the vehicle 8 V or more<\/span>?<\/div>\n
2. Is the ignition switched to ACC or ON (engine off or on)?<\/div>\n<\/dd>\n<\/dl>\n<\/dd>\n<\/dl>\n<\/dd>\n<\/dl>\n

\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
\n

Error code<\/p>\n<\/th>\n

\n

Detection Condition<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
03<\/div>\n<\/td>\n
\n
Target marker No.1 of rear mount camera is not detected<\/div>\n<\/td>\n<\/tr>\n
\n
04<\/div>\n<\/td>\n
\n
Target marker No.2 of rear mount camera is not detected<\/div>\n<\/td>\n<\/tr>\n
\n
06<\/div>\n<\/td>\n
\n
Target marker No.1 of side camera (LH) is not detected<\/div>\n<\/td>\n<\/tr>\n
\n
07<\/div>\n<\/td>\n
\n
Target marker No.2 of side camera (LH) is not detected<\/div>\n<\/td>\n<\/tr>\n
\n
09<\/div>\n<\/td>\n
\n
Target marker No.1 of front camera is not detected<\/div>\n<\/td>\n<\/tr>\n
\n
0A<\/div>\n<\/td>\n
\n
Target marker No.2 of front camera is not detected<\/div>\n<\/td>\n<\/tr>\n
\n
0C<\/div>\n<\/td>\n
\n
Target marker No.1 of side camera (RH) is not detected<\/div>\n<\/td>\n<\/tr>\n
\n
0D<\/div>\n<\/td>\n
\n
Target marker No.2 of side camera (RH) is not detected<\/div>\n<\/td>\n<\/tr>\n
\n
10<\/div>\n<\/td>\n
\n
Input vehicle value exceeds specification<\/div>\n<\/td>\n<\/tr>\n
\n
12<\/div>\n<\/td>\n
\n
Because the following aiming implementation conditions are not met, the aiming is not completed.<\/div>\n
\u2022 Vehicle stopped<\/div>\n
\u2022 All doors (front door, rear door) and trunk lid (4SD)\/liftgate (5HB) closed<\/div>\n
\u2022 Outer mirrors unfolded<\/div>\n
\u2022 Electric parking brake operated<\/div>\n
\u2022 Selector lever is in P position (ATX)<\/div>\n
\u2022 Shift lever is in neutral position (MTX)<\/div>\n<\/td>\n<\/tr>\n
\n
15<\/div>\n<\/td>\n
\n
Aiming is not possible due to malfunction in 360\u00b0 view monitor control module<\/div>\n<\/td>\n<\/tr>\n
\n
16<\/div>\n<\/td>\n
\n
360\u00b0 view monitor control module cannot receive rear mount camera images<\/div>\n<\/td>\n<\/tr>\n
\n
17<\/div>\n<\/td>\n
\n
360\u00b0 view monitor control module cannot receive side camera (LH) images<\/div>\n<\/td>\n<\/tr>\n
\n
18<\/div>\n<\/td>\n
\n
360\u00b0 view monitor control module cannot receive front camera images<\/div>\n<\/td>\n<\/tr>\n
\n
19<\/div>\n<\/td>\n
\n
360\u00b0 view monitor control module cannot receive side camera (RH) images<\/div>\n<\/td>\n<\/tr>\n
\n
1A<\/div>\n<\/td>\n
\n
Power supply to camera insufficient<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

\n

Error code 03\/04\/06\/07\/09\/0A\/0C\/0D\/10<\/p>\n\n\n\n\n\n\n\n\n\n\n
\n

Step<\/p>\n<\/th>\n

\n

Inspection<\/p>\n<\/th>\n

\n

Action<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
1<\/div>\n<\/td>\n
\n
VERIFY TARGET MARKER SETTING ENVIRONMENT AND POSITION<\/div>\n
\u2022 Verify the following.<\/div>\n
\n
\n
\u2015 The vehicle and target marker setting screen are set on level ground.<\/div>\n
\u2015 The target marker is set to the position indicated in the aiming procedure.<\/div>\n
\u2015 There is no dirt, cracks, damage, or wrinkling on the target marker.<\/div>\n
\u2015 The area around the camera or target marker is not shaded.<\/div>\n
\u2015 There is no obstruction or moving object.<\/div>\n
\u2015 The target marker has not moved or the target marker does not move during aiming.<\/div>\n<\/dd>\n<\/dl>\n
\u2022 Display the screen of the 360\u00b0 view monitor system in the center display by pressing the 360\u00b0 view monitor switch.<\/div>\n
\n
\n
\u2015 Does the target marker reflect light?<\/div>\n<\/dd>\n<\/dl>\n
\u2022 Is there a malfunction?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair the malfunctioning location and go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
2<\/div>\n<\/td>\n
\n
PERFORM 360\u00b0 VIEW MONITOR SYSTEM AIMING<\/div>\n
\u2022 Perform the 360\u00b0 view monitor system aiming.<\/div>\n
\u2022 Was the 360\u00b0 view monitor system aiming procedure completed correctly?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
The 360\u00b0 view monitor system aiming is completed. Perform the 360\u00b0 view monitor system screen display verification procedure.<\/div>\n
(See 360\u00b0 View Monitor System Screen Display Verification Procedure<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
If error code 03\/04\/06\/07\/09\/0A\/0C\/0D\/10 is displayed<\/div>\n
\u2022 Go to the next step.<\/div>\n
If code other than error code 03\/04\/06\/07\/09\/0A\/0C\/0D\/10 is displayed<\/div>\n
\u2022 Go to the procedure for the displayed error code.<\/div>\n<\/td>\n<\/tr>\n
\n
3<\/div>\n<\/td>\n
\n
VERIFY DTCs<\/div>\n
\u2022 Perform the DTC inspection. (See DTC INSPECTION<\/a>.)<\/div>\n
\u2022 Is a DTC displayed?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the applicable DTC inspection.<\/div>\n
(See DTC TABLE [360\u00b0VIEW MONITOR CONTROL MODULE (US)]<\/a>.)<\/div>\n
(See DTC TABLE [VEHICLE CONTROL MODULE (US)]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
If the 360\u00b0 view monitor system aiming is not completed correctly after performing the 360\u00b0 view monitor system aiming again, replace the 360\u00b0 view monitor control module.<\/div>\n
(See 360\u00b0VIEW MONITOR CONTROL MODULE REMOVAL\/INSTALLATION [(US)]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

\n

Error code 12\/15\/16\/17\/18\/19\/1A<\/p>\n\n\n\n\n\n\n\n\n
\n

Step<\/p>\n<\/th>\n

\n

Inspection<\/p>\n<\/th>\n

\n

Action<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
1<\/div>\n<\/td>\n
\n
PERFORM 360\u00b0 VIEW MONITOR SYSTEM AIMING<\/div>\n
\u2022 Perform the 360\u00b0 view monitor system aiming.<\/div>\n
\u2022 Was the 360\u00b0 view monitor system aiming procedure completed correctly?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
The 360\u00b0 view monitor system aiming is completed. Perform the 360\u00b0 view monitor system screen display verification procedure.<\/div>\n
(See 360\u00b0 View Monitor System Screen Display Verification Procedure<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
If error code 12\/15\/16\/17\/18\/19\/1A is displayed<\/div>\n
\u2022 Go to the next step.<\/div>\n
If code other than error code 12\/15\/16\/17\/18\/19\/1A is displayed<\/div>\n
\u2022 Go to the procedure for the displayed error code.<\/div>\n<\/td>\n<\/tr>\n
\n
2<\/div>\n<\/td>\n
\n
VERIFY DTCs<\/div>\n
\u2022 Perform the DTC inspection. (See DTC INSPECTION<\/a>.)<\/div>\n
\u2022 Is a DTC displayed?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the applicable DTC inspection.<\/div>\n
(See DTC TABLE [360\u00b0VIEW MONITOR CONTROL MODULE (US)]<\/a>.)<\/div>\n
(See DTC TABLE [VEHICLE CONTROL MODULE (US)]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
If the 360\u00b0 view monitor system aiming is not completed correctly after performing the 360\u00b0 view monitor system aiming again, replace the 360\u00b0 view monitor control module.<\/div>\n
(See 360\u00b0VIEW MONITOR CONTROL MODULE REMOVAL\/INSTALLATION [(US)]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n



\n<\/a><\/p>\n

Front Camera Aiming Procedure<\/p>\n

1.Position the SSTs<\/span> at the positions shown in the figure.<\/p>\n

\n\n\n\n
\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00036910<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

2.Connect the M-MDS to the DLC-2.<\/p>\n

\n

3.Close all the doors (front door, rear door) and the trunk lid (4SD)\/liftgate (5HB).<\/p>\n

\n

4.Verify that the outer mirrors are unfolded.<\/p>\n

\n

5.Operate the electric parking brake.<\/p>\n

\n

6.Shift the selector lever to the P position. (ATX)<\/p>\n

\n

7.Shift the shift lever to the neutral position. (MTX)<\/p>\n

\n

8.After vehicle identification is completed, select the following from the M-MDS initial screen.<\/p>\n

\n

\n
(1)[Toolbox]<\/dd>\n
<\/dd>\n<\/dl>\n
\n
(2)[Work Support]<\/dd>\n
<\/dd>\n<\/dl>\n
\n
(3)[i-ACTIVSENSE]<\/dd>\n
<\/dd>\n<\/dl>\n
\n
(4)[Static aiming]<\/dd>\n
<\/dd>\n<\/dl>\n
\n
(5)[Static aiming for 360\u00b0 View Monitor System]<\/dd>\n
<\/dd>\n<\/dl>\n

9.Perform the front camera aiming procedure according to the directions on the M-MDS.<\/p>\n

\n

10.Verify the M-MDS display.<\/p>\n

\n

\n
\n
\u2022 If [Procedure completed successfully] is displayed<\/div>\n
\n
\n
\u2015 Perform the 360\u00b0 view monitor system screen display verification procedure. (See 360\u00b0 View Monitor System Screen Display Verification Procedure<\/a>.)<\/div>\n<\/dd>\n<\/dl>\n<\/dd>\n<\/dl>\n
\n
\n
\u2022 If [Procedure not completed successfully] is displayed.<\/div>\n
\n
\n
\u2015 Perform an inspection according to the following table for the error code procedure.<\/div>\n
\u2015 If an error code other than the error codes in the following table is displayed, verify the following and perform the front camera aiming again if there is no malfunction, as there could be a communication error between the 360\u00b0 view monitor control module and the diagnostic tester.<\/div>\n
\n
\n
1. Is the battery positive voltage for the vehicle 8 V or more<\/span>?<\/div>\n
2. Is the ignition switched to ACC or ON (engine off or on)?<\/div>\n<\/dd>\n<\/dl>\n<\/dd>\n<\/dl>\n<\/dd>\n<\/dl>\n

\n\n\n\n\n\n\n\n\n\n\n\n
\n

Error code<\/p>\n<\/th>\n

\n

Detection Condition<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
09<\/div>\n<\/td>\n
\n
Target marker No.1 of front camera is not detected<\/div>\n<\/td>\n<\/tr>\n
\n
0A<\/div>\n<\/td>\n
\n
Target marker No.2 of front camera is not detected<\/div>\n<\/td>\n<\/tr>\n
\n
10<\/div>\n<\/td>\n
\n
Input vehicle value exceeds specification<\/div>\n<\/td>\n<\/tr>\n
\n
12<\/div>\n<\/td>\n
\n
Because the following aiming implementation conditions are not met, the aiming is not completed.<\/div>\n
\u2022 Vehicle stopped<\/div>\n
\u2022 All doors (front door, rear door) and trunk lid (4SD)\/liftgate (5HB) closed<\/div>\n
\u2022 Outer mirrors unfolded<\/div>\n
\u2022 Electric parking brake operated<\/div>\n
\u2022 Selector lever is in P position (ATX)<\/div>\n
\u2022 Shift lever is in neutral position (MTX)<\/div>\n<\/td>\n<\/tr>\n
\n
15<\/div>\n<\/td>\n
\n
Aiming is not possible due to malfunction in 360\u00b0 view monitor control module<\/div>\n<\/td>\n<\/tr>\n
\n
18<\/div>\n<\/td>\n
\n
360\u00b0 view monitor control module cannot receive front camera images<\/div>\n<\/td>\n<\/tr>\n
\n
1A<\/div>\n<\/td>\n
\n
Power supply to camera insufficient<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

\n

Error code 09\/0A\/10<\/p>\n\n\n\n\n\n\n\n\n\n\n
\n

Step<\/p>\n<\/th>\n

\n

Inspection<\/p>\n<\/th>\n

\n

Action<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
1<\/div>\n<\/td>\n
\n
VERIFY TARGET MARKER SETTING ENVIRONMENT AND POSITION<\/div>\n
\u2022 Verify the following.<\/div>\n
\n
\n
\u2015 The vehicle and target marker setting screen are set on level ground.<\/div>\n
\u2015 The target marker is set to the position indicated in the aiming procedure.<\/div>\n
\u2015 There is no dirt, cracks, damage, or wrinkling on the target marker.<\/div>\n
\u2015 The area around the front camera or target marker is not shaded.<\/div>\n
\u2015 There is no obstruction or moving object.<\/div>\n
\u2015 The target marker has not moved or the target marker does not move during aiming.<\/div>\n<\/dd>\n<\/dl>\n
\u2022 Display the screen of the 360\u00b0 view monitor system in the center display by pressing the 360\u00b0 view monitor switch.<\/div>\n
\n
\n
\u2015 Does the target marker reflect light?<\/div>\n<\/dd>\n<\/dl>\n
\u2022 Is there a malfunction?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair the malfunctioning location and go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
2<\/div>\n<\/td>\n
\n
PERFORM FRONT CAMERA AIMING<\/div>\n
\u2022 Perform the front camera aiming.<\/div>\n
\u2022 Was the front camera aiming procedure completed correctly?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
The front camera aiming is completed. Perform the 360\u00b0 view monitor system screen display verification procedure.<\/div>\n
(See 360\u00b0 View Monitor System Screen Display Verification Procedure<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
If error code 09\/0A\/10 is displayed<\/div>\n
\u2022 Go to the next step.<\/div>\n
If code other than error code 09\/0A\/10 is displayed<\/div>\n
\u2022 Go to the procedure for the displayed error code.<\/div>\n<\/td>\n<\/tr>\n
\n
3<\/div>\n<\/td>\n
\n
VERIFY DTCs<\/div>\n
\u2022 Perform the DTC inspection. (See DTC INSPECTION<\/a>.)<\/div>\n
\u2022 Is a DTC displayed?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the applicable DTC inspection.<\/div>\n
(See DTC TABLE [360\u00b0VIEW MONITOR CONTROL MODULE (US)]<\/a>.)<\/div>\n
(See DTC TABLE [VEHICLE CONTROL MODULE (US)]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
If the front camera aiming is not completed correctly after performing the front camera aiming again, replace the 360\u00b0 view monitor control module.<\/div>\n
(See 360\u00b0VIEW MONITOR CONTROL MODULE REMOVAL\/INSTALLATION [(US)]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

\n

Error code 12\/15\/18\/1A<\/p>\n\n\n\n\n\n\n\n\n
\n

Step<\/p>\n<\/th>\n

\n

Inspection<\/p>\n<\/th>\n

\n

Action<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
1<\/div>\n<\/td>\n
\n
PERFORM FRONT CAMERA AIMING<\/div>\n
\u2022 Perform the front camera aiming.<\/div>\n
\u2022 Was the front camera aiming procedure completed correctly?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
The front camera aiming is completed. Perform the 360\u00b0 view monitor system screen display verification procedure.<\/div>\n
(See 360\u00b0 View Monitor System Screen Display Verification Procedure<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
If error code 12\/15\/18\/1A is displayed<\/div>\n
\u2022 Go to the next step.<\/div>\n
If code other than error code 12\/15\/18\/1A is displayed<\/div>\n
\u2022 Go to the procedure for the displayed error code.<\/div>\n<\/td>\n<\/tr>\n
\n
2<\/div>\n<\/td>\n
\n
VERIFY DTCs<\/div>\n
\u2022 Perform the DTC inspection. (See DTC INSPECTION<\/a>.)<\/div>\n
\u2022 Is a DTC displayed?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the applicable DTC inspection.<\/div>\n
(See DTC TABLE [360\u00b0VIEW MONITOR CONTROL MODULE (US)]<\/a>.)<\/div>\n
(See DTC TABLE [VEHICLE CONTROL MODULE (US)]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
If the front camera aiming is not completed correctly after performing the front camera aiming again, replace the 360\u00b0 view monitor control module.<\/div>\n
(See 360\u00b0VIEW MONITOR CONTROL MODULE REMOVAL\/INSTALLATION [(US)]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n



\n<\/a><\/p>\n

Side Camera Aiming Procedure<\/p>\n

\n
\n
Note<\/div>\n<\/dd>\n
\n
\u2022 For the side camera aiming, 1 set(1 set\/2 targets) of the SST (49 JP04 001)<\/span> are required.<\/div>\n<\/dd>\n<\/dl>\n

1.Position the SSTs<\/span> at the positions shown in the figure.<\/p>\n

\n\n\n\n
\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00036911<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

2.Connect the M-MDS to the DLC-2.<\/p>\n

\n

3.Close all the doors (front door, rear door) and the trunk lid (4SD)\/liftgate (5HB).<\/p>\n

\n

4.Verify that the outer mirrors are unfolded.<\/p>\n

\n

5.Operate the electric parking brake.<\/p>\n

\n

6.Shift the selector lever to the P position. (ATX)<\/p>\n

\n

7.Shift the shift lever to the neutral position. (MTX)<\/p>\n

\n

8.After vehicle identification is completed, select the following from the M-MDS initial screen.<\/p>\n

\n

\n
(1)[Toolbox]<\/dd>\n
<\/dd>\n<\/dl>\n
\n
(2)[Work Support]<\/dd>\n
<\/dd>\n<\/dl>\n
\n
(3)[i-ACTIVSENSE]<\/dd>\n
<\/dd>\n<\/dl>\n
\n
(4)[Static aiming]<\/dd>\n
<\/dd>\n<\/dl>\n
\n
(5)[Static aiming for 360\u00b0 View Monitor System]<\/dd>\n
<\/dd>\n<\/dl>\n

9.Perform side camera aiming procedure according to the directions on the M-MDS.<\/p>\n

\n

10.Verify the M-MDS display.<\/p>\n

\n

\n
\n
\u2022 If [Procedure completed successfully] is displayed<\/div>\n
\n
\n
\u2015 The side camera aiming is completed. Perform the 360\u00b0 view monitor system screen display verification procedure. (See 360\u00b0 View Monitor System Screen Display Verification Procedure<\/a>.)<\/div>\n<\/dd>\n<\/dl>\n<\/dd>\n<\/dl>\n
\n
\n
\u2022 If [Procedure not completed successfully] is displayed.<\/div>\n
\n
\n
\u2015 Perform an inspection according to the following table for the error code procedure.<\/div>\n
\u2015 If an error code other than the error codes in the following table is displayed, verify the following and perform the side camera aiming again if there is no malfunction, as there could be a communication error between the 360\u00b0 view monitor control module and the diagnostic tester.<\/div>\n
\n
\n
1. Is the battery positive voltage for the vehicle 8 V or more<\/span>?<\/div>\n
2. Is the ignition switched to ACC or ON (engine off or on)?<\/div>\n<\/dd>\n<\/dl>\n<\/dd>\n<\/dl>\n<\/dd>\n<\/dl>\n

\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
\n

Error code<\/p>\n<\/th>\n

\n

Detection Condition<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
06<\/div>\n<\/td>\n
\n
Target marker No.1 of side camera (LH) is not detected<\/div>\n<\/td>\n<\/tr>\n
\n
07<\/div>\n<\/td>\n
\n
Target marker No.2 of side camera (LH) is not detected<\/div>\n<\/td>\n<\/tr>\n
\n
0C<\/div>\n<\/td>\n
\n
Target marker No.1 of side camera (RH) is not detected<\/div>\n<\/td>\n<\/tr>\n
\n
0D<\/div>\n<\/td>\n
\n
Target marker No.2 of side camera (RH) is not detected<\/div>\n<\/td>\n<\/tr>\n
\n
10<\/div>\n<\/td>\n
\n
Input vehicle value exceeds specification<\/div>\n<\/td>\n<\/tr>\n
\n
12<\/div>\n<\/td>\n
\n
Because the following aiming implementation conditions are not met, the aiming is not completed.<\/div>\n
\u2022 Vehicle stopped<\/div>\n
\u2022 All doors (front door, rear door) and trunk lid (4SD)\/liftgate (5HB) closed<\/div>\n
\u2022 Outer mirrors unfolded<\/div>\n
\u2022 Electric parking brake operated<\/div>\n
\u2022 Selector lever is in P position (ATX)<\/div>\n
\u2022 Shift lever is in neutral position (MTX)<\/div>\n<\/td>\n<\/tr>\n
\n
15<\/div>\n<\/td>\n
\n
Aiming is not possible due to malfunction in 360\u00b0 view monitor control module<\/div>\n<\/td>\n<\/tr>\n
\n
17<\/div>\n<\/td>\n
\n
360\u00b0 view monitor control module cannot receive side camera (LH) images<\/div>\n<\/td>\n<\/tr>\n
\n
19<\/div>\n<\/td>\n
\n
360\u00b0 view monitor control module cannot receive side camera (RH) images<\/div>\n<\/td>\n<\/tr>\n
\n
1A<\/div>\n<\/td>\n
\n
Power supply to camera insufficient<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

\n

Error code 06\/07\/0C\/0D\/10<\/p>\n\n\n\n\n\n\n\n\n\n\n
\n

Step<\/p>\n<\/th>\n

\n

Inspection<\/p>\n<\/th>\n

\n

Action<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
1<\/div>\n<\/td>\n
\n
VERIFY TARGET MARKER SETTING ENVIRONMENT AND POSITION<\/div>\n
\u2022 Verify the following.<\/div>\n
\n
\n
\u2015 The vehicle and target marker setting screen are set on level ground.<\/div>\n
\u2015 The target marker is set to the position indicated in the aiming procedure.<\/div>\n
\u2015 There is no dirt, cracks, damage, or wrinkling on the target marker.<\/div>\n
\u2015 The area around the side cameras or target is not shaded.<\/div>\n
\u2015 There is no obstruction or moving object.<\/div>\n
\u2015 The target marker has not moved or the target marker does not move during aiming.<\/div>\n<\/dd>\n<\/dl>\n
\u2022 Display the screen of the 360\u00b0 view monitor system in the center display by pressing the 360\u00b0 view monitor switch.<\/div>\n
\n
\n
\u2015 Does the target marker reflect light?<\/div>\n<\/dd>\n<\/dl>\n
\u2022 Is there a malfunction?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair the malfunctioning location and go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
2<\/div>\n<\/td>\n
\n
PERFORM SIDE CAMERA AIMING<\/div>\n
\u2022 Perform the side camera aiming.<\/div>\n
\u2022 Was the side camera aiming procedure completed correctly?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
The side camera aiming is completed. Perform the 360\u00b0 view monitor system screen display verification procedure.<\/div>\n
(See 360\u00b0 View Monitor System Screen Display Verification Procedure<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
If error code 06\/07\/0C\/0D\/10 is displayed<\/div>\n
\u2022 Go to the next step.<\/div>\n
If code other than error code 06\/07\/0C\/0D\/10 is displayed<\/div>\n
\u2022 Go to the procedure for the displayed error code.<\/div>\n<\/td>\n<\/tr>\n
\n
3<\/div>\n<\/td>\n
\n
VERIFY DTCs<\/div>\n
\u2022 Perform the DTC inspection. (See DTC INSPECTION<\/a>.)<\/div>\n
\u2022 Is a DTC displayed?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the applicable DTC inspection.<\/div>\n
(See DTC TABLE [360\u00b0VIEW MONITOR CONTROL MODULE (US)]<\/a>.)<\/div>\n
(See DTC TABLE [VEHICLE CONTROL MODULE (US)]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
If the side camera aiming is not completed correctly after performing the side camera aiming again, replace the 360\u00b0 view monitor control module.<\/div>\n
(See 360\u00b0VIEW MONITOR CONTROL MODULE REMOVAL\/INSTALLATION [(US)]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

\n

Error code 12\/15\/17\/19\/1A<\/p>\n\n\n\n\n\n\n\n\n
\n

Step<\/p>\n<\/th>\n

\n

Inspection<\/p>\n<\/th>\n

\n

Action<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
1<\/div>\n<\/td>\n
\n
PERFORM SIDE CAMERA AIMING<\/div>\n
\u2022 Perform the side camera aiming.<\/div>\n
\u2022 Was the side camera aiming procedure completed correctly?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
The side camera aiming is completed. Perform the 360\u00b0 view monitor system screen display verification procedure.<\/div>\n
(See 360\u00b0 View Monitor System Screen Display Verification Procedure<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
If error code 12\/15\/17\/19\/1A is displayed<\/div>\n
\u2022 Go to the next step.<\/div>\n
If code other than error code 12\/15\/17\/19\/1A is displayed<\/div>\n
\u2022 Go to the procedure for the displayed error code.<\/div>\n<\/td>\n<\/tr>\n
\n
2<\/div>\n<\/td>\n
\n
VERIFY DTCs<\/div>\n
\u2022 Perform the DTC inspection. (See DTC INSPECTION<\/a>.)<\/div>\n
\u2022 Is a DTC displayed?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the applicable DTC inspection.<\/div>\n
(See DTC TABLE [360\u00b0VIEW MONITOR CONTROL MODULE (US)]<\/a>.)<\/div>\n
(See DTC TABLE [VEHICLE CONTROL MODULE (US)]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
If the side camera aiming is not completed correctly after performing the side camera aiming again, replace the 360\u00b0 view monitor control module.<\/div>\n
(See 360\u00b0VIEW MONITOR CONTROL MODULE REMOVAL\/INSTALLATION [(US)]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n



\n<\/a><\/p>\n

Rear Mount Camera Aiming Procedure<\/p>\n

1.Position the SSTs<\/span> at the positions shown in the figure.<\/p>\n

\n\n\n\n
\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00036912<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

2.Connect the M-MDS to the DLC-2.<\/p>\n

\n

3.Close all the doors (front door, rear door) and the trunk lid (4SD)\/liftgate (5HB).<\/p>\n

\n

4.Verify that the outer mirrors are unfolded.<\/p>\n

\n

5.Operate the electric parking brake.<\/p>\n

\n

6.Shift the selector lever to the P position. (ATX)<\/p>\n

\n

7.Shift the shift lever to the neutral position. (MTX)<\/p>\n

\n

8.After vehicle identification is completed, select the following from the M-MDS initial screen.<\/p>\n

\n

\n
(1)[Toolbox]<\/dd>\n
<\/dd>\n<\/dl>\n
\n
(2)[Work Support]<\/dd>\n
<\/dd>\n<\/dl>\n
\n
(3)[i-ACTIVSENSE]<\/dd>\n
<\/dd>\n<\/dl>\n
\n
(4)[Static aiming]<\/dd>\n
<\/dd>\n<\/dl>\n
\n
(5)[Static aiming for 360\u00b0 View Monitor System]<\/dd>\n
<\/dd>\n<\/dl>\n

9.Perform the rear mount camera aiming procedure according to the directions on the M-MDS.<\/p>\n

\n

10.Verify the M-MDS display.<\/p>\n

\n

\n
\n
\u2022 If [Procedure completed successfully] is displayed<\/div>\n
\n
\n
\u2015 The rear mount camera aiming is completed. Perform the 360\u00b0 view monitor system screen display verification procedure. (See 360\u00b0 View Monitor System Screen Display Verification Procedure<\/a>.)<\/div>\n<\/dd>\n<\/dl>\n<\/dd>\n<\/dl>\n
\n
\n
\u2022 If [Procedure not completed successfully] is displayed.<\/div>\n
\n
\n
\u2015 Perform an inspection according to the following table for the error code procedure.<\/div>\n
\u2015 If an error code other than the error codes in the following table is displayed, verify the following and perform the rear mount camera aiming again if there is no malfunction, as there could be a communication error between the 360\u00b0 view monitor control module and the diagnostic tester.<\/div>\n
\n
\n
1. Is the battery positive voltage for the vehicle 8 V or more<\/span>?<\/div>\n
2. Is the ignition switched to ACC or ON (engine off or on)?<\/div>\n<\/dd>\n<\/dl>\n<\/dd>\n<\/dl>\n<\/dd>\n<\/dl>\n

\n\n\n\n\n\n\n\n\n\n\n\n
\n

Error code<\/p>\n<\/th>\n

\n

Detection Condition<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
03<\/div>\n<\/td>\n
\n
Target marker No.1 of rear mount camera is not detected<\/div>\n<\/td>\n<\/tr>\n
\n
04<\/div>\n<\/td>\n
\n
Target marker No.2 of rear mount camera is not detected<\/div>\n<\/td>\n<\/tr>\n
\n
10<\/div>\n<\/td>\n
\n
Input vehicle value exceeds specification<\/div>\n<\/td>\n<\/tr>\n
\n
12<\/div>\n<\/td>\n
\n
Because the following aiming implementation conditions are not met, the aiming is not completed.<\/div>\n
\u2022 Vehicle stopped<\/div>\n
\u2022 All doors (front door, rear door) and trunk lid (4SD)\/liftgate (5HB) closed<\/div>\n
\u2022 Outer mirrors unfolded<\/div>\n
\u2022 Electric parking brake operated<\/div>\n
\u2022 Selector lever is in P position (ATX)<\/div>\n
\u2022 Shift lever is in neutral position (MTX)<\/div>\n<\/td>\n<\/tr>\n
\n
15<\/div>\n<\/td>\n
\n
Aiming is not possible due to malfunction in 360\u00b0 view monitor control module<\/div>\n<\/td>\n<\/tr>\n
\n
16<\/div>\n<\/td>\n
\n
360\u00b0 view monitor control module cannot receive rear mount camera images<\/div>\n<\/td>\n<\/tr>\n
\n
1A<\/div>\n<\/td>\n
\n
Power supply to camera insufficient<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

\n

Error code 03\/04\/10<\/p>\n\n\n\n\n\n\n\n\n\n\n
\n

Step<\/p>\n<\/th>\n

\n

Inspection<\/p>\n<\/th>\n

\n

Action<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
1<\/div>\n<\/td>\n
\n
VERIFY TARGET MARKER SETTING ENVIRONMENT AND POSITION<\/div>\n
\u2022 Verify the following.<\/div>\n
\n
\n
\u2015 The vehicle and target marker setting screen are set on level ground.<\/div>\n
\u2015 The target marker is set to the position indicated in the aiming procedure.<\/div>\n
\u2015 There is no dirt, cracks, damage, or wrinkling on the target marker.<\/div>\n
\u2015 The area around the rear mount camera or target is not shaded.<\/div>\n
\u2015 There is no obstruction or moving object.<\/div>\n
\u2015 The target marker has not moved or the target marker does not move during aiming.<\/div>\n<\/dd>\n<\/dl>\n
\u2022 Display the screen of the 360\u00b0 view monitor system in the center display by pressing the 360\u00b0 view monitor switch.<\/div>\n
\n
\n
\u2015 Does the target marker reflect light?<\/div>\n<\/dd>\n<\/dl>\n
\u2022 Is there a malfunction?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair the malfunctioning location and go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
2<\/div>\n<\/td>\n
\n
PERFORM REAR MOUNT CAMERA AIMING<\/div>\n
\u2022 Perform the rear mount camera aiming.<\/div>\n
\u2022 Was the rear mount camera aiming procedure completed correctly?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
The rear mount camera aiming is completed. Perform the 360\u00b0 view monitor system screen display verification procedure.<\/div>\n
(See 360\u00b0 View Monitor System Screen Display Verification Procedure<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
If error code 03\/04\/10 is displayed<\/div>\n
\u2022 Go to the next step.<\/div>\n
If code other than error code 03\/04\/10 is displayed<\/div>\n
\u2022 Go to the procedure for the displayed error code.<\/div>\n<\/td>\n<\/tr>\n
\n
3<\/div>\n<\/td>\n
\n
VERIFY DTCs<\/div>\n
\u2022 Perform the DTC inspection. (See DTC INSPECTION<\/a>.)<\/div>\n
\u2022 Is a DTC displayed?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the applicable DTC inspection.<\/div>\n
(See DTC TABLE [360\u00b0VIEW MONITOR CONTROL MODULE (US)]<\/a>.)<\/div>\n
(See DTC TABLE [VEHICLE CONTROL MODULE (US)]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
If the rear mount camera aiming is not completed correctly after performing the rear mount camera aiming again, replace the 360\u00b0 view monitor control module.<\/div>\n
(See 360\u00b0VIEW MONITOR CONTROL MODULE REMOVAL\/INSTALLATION [(US)]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

\n

Error code 12\/15\/16\/1A<\/p>\n\n\n\n\n\n\n\n\n
\n

Step<\/p>\n<\/th>\n

\n

Inspection<\/p>\n<\/th>\n

\n

Action<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
1<\/div>\n<\/td>\n
\n
PERFORM REAR MOUNT CAMERA AIMING<\/div>\n
\u2022 Perform the rear mount camera aiming.<\/div>\n
\u2022 Was the rear mount camera aiming procedure completed correctly?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
The rear mount camera aiming is completed. Perform the 360\u00b0 view monitor system screen display verification procedure.<\/div>\n
(See 360\u00b0 View Monitor System Screen Display Verification Procedure<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
If error code 12\/15\/16\/1A is displayed<\/div>\n
\u2022 Go to the next step.<\/div>\n
If code other than error code 12\/15\/16\/1A is displayed<\/div>\n
\u2022 Go to the procedure for the displayed error code.<\/div>\n<\/td>\n<\/tr>\n
\n
2<\/div>\n<\/td>\n
\n
VERIFY DTCs<\/div>\n
\u2022 Perform the DTC inspection. (See DTC INSPECTION<\/a>.)<\/div>\n
\u2022 Is a DTC displayed?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the applicable DTC inspection.<\/div>\n
(See DTC TABLE [360\u00b0VIEW MONITOR CONTROL MODULE (US)]<\/a>.)<\/div>\n
(See DTC TABLE [VEHICLE CONTROL MODULE (US)]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
If the rear mount camera aiming is not completed correctly after performing the rear mount camera aiming again, replace the 360\u00b0 view monitor control module.<\/div>\n
(See 360\u00b0VIEW MONITOR CONTROL MODULE REMOVAL\/INSTALLATION [(US)]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n
<\/div>\n
<\/div>\n
<\/div>\n

<\/div>\n<\/div>\n","protected":false},"excerpt":{"rendered":"

360\u00b0VIEW MONITOR SYSTEM AIMING SM2337173 id152000010200 Special service tool (SST) 49 L067 006 Plumb bob 49 JP04 001 Target marker Preparation Before Servicing 1.Empty the vehicle by having all occupants leave the vehicle and remove all the cargo except for the spare tire, jack and tools equipped on the vehicle. 2.Adjust the air pressure of each tire to the specified value. (See WHEEL AND TIRE SPECIFICATION [(US)].) 3.Move the vehicle to level ground. Caution \u2022 […]<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_monsterinsights_skip_tracking":false,"_monsterinsights_sitenote_active":false,"_monsterinsights_sitenote_note":"","_monsterinsights_sitenote_category":0,"footnotes":""},"class_list":["post-9645","page","type-page","status-publish","hentry"],"_links":{"self":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages\/9645","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/comments?post=9645"}],"version-history":[{"count":0,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages\/9645\/revisions"}],"wp:attachment":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/media?parent=9645"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}