{"id":9147,"date":"2022-03-10T20:30:45","date_gmt":"2022-03-10T20:30:45","guid":{"rendered":"https:\/\/www.hexorcism.com\/19BP\/sm2335532\/"},"modified":"2022-03-10T20:30:45","modified_gmt":"2022-03-10T20:30:45","slug":"sm2335532","status":"publish","type":"page","link":"https:\/\/www.hexorcism.com\/19BP\/sm2335532\/","title":{"rendered":"TIE-ROD END REPLACEMENT"},"content":{"rendered":"
\n

TIE-ROD END REPLACEMENT<\/h3>\n<\/div>\n

SM2335532<\/p>\n

<\/p>\n
\n
\n
\n

id061300801200<\/p>\n

Special service tool (SST)<\/p>\n\n\n\n
\n
49 T028 3A0<\/div>\n
<\/div>\n
Ball joint puller set<\/div>\n<\/td>\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

Replacement part<\/p>\n\n\n\n
\n
Snap pin<\/div>\n
<\/div>\n
Quantity: 1<\/div>\n
<\/div>\n
Location of use: Tie-rod end<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n



\n<\/a><\/p>\n

Removal<\/p>\n

1.Remove the wheel and tire. (See WHEEL AND TIRE REMOVAL\/INSTALLATION<\/a>.)<\/p>\n

\n

2.Remove the snap pin from the tie-rod end.<\/p>\n

\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00023114<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

3.Loosen the locknut of the tie-rod end.<\/p>\n

\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00023115<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

4.Detach the tie-rod end from the steering knuckle using the SST<\/span>.<\/p>\n

\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
ac8wzw00001479<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

5.Remove the locknut of the tie-rod end.<\/p>\n

\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00023116<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

6.Place alignment marks as shown in the figure for reference in tie-rod end assembly.<\/p>\n

\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00023117<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

7.Remove the tie-rod end.<\/p>\n

\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00023118<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n



\n<\/a><\/p>\n

Installation<\/p>\n

1.Place alignment marks on the new tie-rod end in the same positions as the removed tie-rod end.<\/p>\n

\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00023119<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

2.Align the marks that were made before removing the tie-rod end, and assemble the tie-rod end to the tie rod.<\/p>\n

\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00023120<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

3.Verify that dimension A shown in the figure is within the standard.<\/p>\n

\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00027965<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
\n
\n
\n
Standard<\/div>\n<\/dd>\n<\/dl>\n
\n
\n
5.8\u201418.8 mm {0.23\u20140.74 in}<\/div>\n<\/dd>\n<\/dl>\n<\/div>\n
\n
\n
\u2022 If not within the standard, make adjustments so that dimension A is within the standard.<\/div>\n<\/dd>\n<\/dl>\n

4.Install the tie-rod end to the steering knuckle.<\/p>\n

\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00023122<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

5.Install a new snap pin.<\/p>\n

\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00023123<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

6.Install the wheel and tire. (See WHEEL AND TIRE REMOVAL\/INSTALLATION<\/a>.)<\/p>\n

\n

7.Verify that A and B shown in the figure are parallel while the vehicle is on the ground.<\/p>\n

\n\n\n\n
\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00033056<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
\n
\n
Caution<\/div>\n<\/dd>\n
\n
\u2022 Install the tie-rod end to the correct position. Otherwise, it could cause cracks on the tie-rod end boot.<\/div>\n<\/dd>\n<\/dl>\n
\n
\n
\u2022 If the installation position is not correct, perform the adjustment using the following procedure.<\/div>\n
\n
\n
1. Adjust the tie-rod end by rotating it so that it is at the correct position.<\/p>\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
ac8wzw00003230<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/dd>\n<\/dl>\n<\/dd>\n<\/dl>\n

8.After installation, inspect the front wheel alignment. (See FRONT WHEEL ALIGNMENT [(US)]<\/a>.)<\/p>\n

\n<\/div>\n

<\/div>\n
<\/div>\n
<\/div>\n

<\/div>\n<\/div>\n","protected":false},"excerpt":{"rendered":"

TIE-ROD END REPLACEMENT SM2335532 id061300801200 Special service tool (SST) 49 T028 3A0 Ball joint puller set Replacement part Snap pin Quantity: 1 Location of use: Tie-rod end Removal 1.Remove the wheel and tire. (See WHEEL AND TIRE REMOVAL\/INSTALLATION.) 2.Remove the snap pin from the tie-rod end. am3zzw00023114 3.Loosen the locknut of the tie-rod end. am3zzw00023115 4.Detach the tie-rod end from the steering knuckle using the SST. ac8wzw00001479 5.Remove the locknut of the tie-rod end. am3zzw00023116 […]<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_monsterinsights_skip_tracking":false,"_monsterinsights_sitenote_active":false,"_monsterinsights_sitenote_note":"","_monsterinsights_sitenote_category":0,"footnotes":""},"class_list":["post-9147","page","type-page","status-publish","hentry"],"_links":{"self":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages\/9147","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/comments?post=9147"}],"version-history":[{"count":0,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages\/9147\/revisions"}],"wp:attachment":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/media?parent=9147"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}