{"id":8822,"date":"2022-03-10T20:30:42","date_gmt":"2022-03-10T20:30:42","guid":{"rendered":"https:\/\/www.hexorcism.com\/19BP\/sm2334366\/"},"modified":"2022-03-10T20:30:42","modified_gmt":"2022-03-10T20:30:42","slug":"sm2334366","status":"publish","type":"page","link":"https:\/\/www.hexorcism.com\/19BP\/sm2334366\/","title":{"rendered":"DTC P0087:00 [PCM (SKYACTIV-G)]"},"content":{"rendered":"
\n

DTC P0087:00 [PCM (SKYACTIV-G)]<\/h3>\n<\/div>\n

SM2334366<\/p>\n

<\/p>\n
\n
\n
\n

id0102t4008200<\/p>\n

\n
\n
Note<\/div>\n<\/dd>\n
\n
\u2022 To determine the malfunctioning part, proceed with the diagnostics from “Function Inspection Using M-MDS”.<\/div>\n<\/dd>\n<\/dl>\n



\n<\/a><\/p>\n

Details On DTCs<\/p>\n

\n\n\n\n\n\n\n\n\n\n\n\n\n\n
\n

Description<\/p>\n<\/th>\n

\n

Fuel pressure sensor circuit range\/performance problem<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
Detection condition<\/span><\/div>\n<\/td>\n
\n
Determination conditions<\/div>\n<\/td>\n
\n
\u2022 If any of the following conditions is met under condition A or condition B:<\/div>\n
\n
\n
Condition A:<\/div>\n<\/dd>\n
\n
\u2015 The actual fuel pressure is lower than the target fuel pressure by 1.2 MPa {12 kgf\/cm2<\/sup>, 174 psi}<\/span> or more even though the fuel pressure feedback amount is maintained high.<\/div>\n<\/dd>\n<\/dl>\n
\n
\n
Condition B:<\/div>\n<\/dd>\n
\n
\u2015 The PCM detects that the actual fuel pressure is 1.7 MPa {17 kgf\/cm2<\/sup>, 247 psi} or less<\/span> continuously or intermittently.<\/div>\n<\/dd>\n<\/dl>\n<\/td>\n<\/tr>\n
\n
Preconditions<\/div>\n<\/td>\n
\n
\u2022 Engine speed: 500 rpm or more<\/span> *1<\/sup><\/div>\n
\u2022 The following DTCs are not detected:<\/div>\n
\n
\n
\u2015 Fuel pressure sensor: P0089:00, P0192:00 and P0193:00<\/div>\n
\u2015 High pressure fuel pump: P0091:00 and P0092:00<\/div>\n<\/dd>\n<\/dl>\n
*1<\/sup>: Standard can be verified by displaying PIDs using M-MDS<\/div>\n<\/td>\n<\/tr>\n
\n
Malfunction determination period<\/div>\n<\/td>\n
\n
Condition A:<\/div>\n
\u2022 5 s<\/span> period<\/div>\n
Condition B:<\/div>\n
\u2022 Specified time<\/div>\n<\/td>\n<\/tr>\n
\n
Drive cycle<\/div>\n<\/td>\n
\n
\u2022 1<\/div>\n<\/td>\n<\/tr>\n
\n
Self test type<\/div>\n<\/td>\n
\n
\u2022 CMDTC self test<\/div>\n<\/td>\n<\/tr>\n
\n
Sensor used<\/div>\n<\/td>\n
\n
\u2022 Fuel pressure sensor<\/div>\n<\/td>\n<\/tr>\n
\n
Fail-safe function<\/span><\/div>\n<\/td>\n
\n
\u2022 Limits intake air amount<\/div>\n
\u2022 Stops high pressure fuel pump control<\/div>\n<\/td>\n<\/tr>\n
\n
Vehicle status when DTCs are output<\/span><\/div>\n<\/td>\n
\n
\u2022 Not applicable<\/div>\n<\/td>\n<\/tr>\n
\n
Possible cause<\/span><\/div>\n<\/td>\n
\n
\u2022 Air suction in fuel line due to fuel is runout<\/div>\n
\u2022 High pressure fuel pump connector or terminals malfunction<\/div>\n
\u2022 Fuel pressure sensor connector or terminals malfunction<\/div>\n
\u2022 PCM connector or terminals malfunction<\/div>\n
\u2022 Fuel pressure sensor malfunction<\/div>\n
\u2022 Fuel delivery system malfunction (insufficient fuel pressure)<\/div>\n
\u2022 Fuel injector malfunction<\/div>\n
\u2022 High pressure fuel pump malfunction<\/div>\n
\n
\n
\u2015 Relief valve (built-into high pressure fuel pump) malfunction<\/div>\n<\/dd>\n<\/dl>\n
\u2022 PCM malfunction<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n



\n<\/a><\/p>\n

System Wiring Diagram<\/p>\n

\u2022 Not applicable<\/div>\n



\n<\/a><\/p>\n

Function Explanation (DTC Detection Outline)<\/p>\n

\u2022 The PCM calculates the target fuel pressure appropriate to the engine conditions relative to the actual fuel pressure based on the fuel pressure sensor signal and provides feedback to the high pressure fuel pump control. If the difference between the actual fuel pressure and the target fuel pressure relative to the feedback amount is large, the PCM determines a malfunction in the fuel pressure sensor and stores a DTC.<\/div>\n



\n<\/a><\/p>\n

Repeatability Verification Procedure<\/p>\n

1. Warm up the engine to allow the engine coolant temperature to reach 80 \u00b0C {176 \u00b0F} or more<\/span>.<\/div>\n
2. Start the engine and leave it idling for 1 min<\/span>.<\/p>\n
\n
\n
Note<\/div>\n<\/dd>\n
\n
\u2022 The target calculated by the PCM is increased and the DTC P0087:00 determination conditions are met by repeating the Step 3 operation.<\/div>\n<\/dd>\n<\/dl>\n<\/div>\n
3. Shift to 1st gear and accelerate\/decelerate the vehicle to 30\u201450 km\/h {19\u201431 mph}<\/span>.<\/p>\n
\n
\n
Note<\/div>\n<\/dd>\n
\n
\u2022 Match the engine coolant temperature in the recorded freeze frame data\/snapshot data, the vehicle speed, and engine speed values to the best extent possible while driving the vehicle.<\/div>\n<\/dd>\n<\/dl>\n<\/div>\n
4. Try to reproduce the malfunction by driving the vehicle for 5 min<\/span> based on the values in the freeze frame data\/snapshot data.<\/div>\n



\n<\/a><\/p>\n

PID Item\/Simulation Item Used In Diagnosis<\/p>\n

\n

PID\/DATA monitor item table<\/p>\n\n\n\n\n\n
\n

PIDs<\/p>\n<\/th>\n

\n

Reference<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
FUEL_PRES<\/div>\n<\/td>\n
\n
(See PID\/DATA MONITOR TABLE [PCM (SKYACTIV-G (US))]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

\n

Simulation item table<\/p>\n\n\n\n\n\n
\n

Simulation items<\/p>\n<\/th>\n

\n

Reference<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
FUEL_PUMP_REQ<\/div>\n<\/td>\n
\n
(See SIMULATION TABLE [PCM (SKYACTIV-G (US))]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n



\n<\/a><\/p>\n

Function Inspection Using M-MDS<\/p>\n

\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
\n

Step<\/p>\n<\/th>\n

\n

Inspection<\/p>\n<\/th>\n

\n

Results<\/p>\n<\/th>\n

\n

Action<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
1<\/div>\n<\/td>\n
\n
PURPOSE: VERIFY RELATED REPAIR INFORMATION OR SERVICE INFORMATION AVAILABILITY<\/div>\n
\u2022 Verify related Service Bulletins, on-line repair information, or Service Information availability.<\/div>\n
\u2022 Is any related Information available?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Perform repair or diagnosis according to the available information.<\/div>\n
\u2022 If the vehicle is not repaired, go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
2<\/div>\n<\/td>\n
\n
PURPOSE: IDENTIFY TRIGGER DTC FOR FREEZE FRAME DATA<\/div>\n
\u2022 Is the DTC P0087:00 on freeze frame data?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the troubleshooting procedure for DTC on freeze frame data.<\/div>\n
(See DTC TABLE [PCM (SKYACTIV-G (US))]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
3<\/div>\n<\/td>\n
\n
PURPOSE: RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION<\/div>\n
\u2022 Record the freeze frame data\/snapshot data.<\/p>\n
\n
\n
Note<\/div>\n<\/dd>\n
\n
\u2022 Recording can be facilitated using the screen capture function of the PC.<\/div>\n<\/dd>\n<\/dl>\n<\/div>\n<\/td>\n
\n
\u2014<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
4<\/div>\n<\/td>\n
\n
PURPOSE: VERIFICATION IF MALFUNCTION CAUSED BY LACK OF FUEL<\/div>\n
\u2022 Verify the snapshot data FLI. (See SNAPSHOT DATA TABLE [PCM (SKYACTIV-G)]<\/a>.)<\/div>\n
\u2022 Is the snapshot data FLI 5% or less<\/span>?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Refill the fuel.<\/div>\n
Go to Troubleshooting Diagnostic Procedure to perform the repair completion verification.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
5<\/div>\n<\/td>\n
\n
PURPOSE: INSPECT FOR OTHER RELATED DTCs<\/div>\n
\u2022 Perform the DTC inspection for the PCM. (See DTC INSPECTION<\/a>.)<\/div>\n
\u2022 Are any other DTCs displayed?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair the malfunctioning location according to the applicable DTC troubleshooting.<\/div>\n
(See DTC TABLE [PCM (SKYACTIV-G (US))]<\/a>.)<\/div>\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
6<\/div>\n<\/td>\n
\n
PURPOSE: VERIFY CONNECTOR CONNECTIONS<\/div>\n
\u2022 Start the engine.<\/div>\n
\u2022 Access the FUEL_PRES PID using the M-MDS. (See PID\/DATA MONITOR INSPECTION<\/a>.)<\/div>\n
\u2022 Does the PID value fluctuate when the following connectors are shaken?<\/div>\n
\n
\n
\u2015 Fuel pressure sensor<\/div>\n
\u2015 PCM<\/div>\n<\/dd>\n<\/dl>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair or replace the applicable wiring harness or connector parts.<\/div>\n
Go to Troubleshooting Diagnostic Procedure to perform the repair completion verification.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
7<\/div>\n<\/td>\n
\n
PURPOSE: VERIFY FUEL PRESSURE (LOW-SIDE) MALFUNCTION<\/div>\n
\n
\n
Note<\/div>\n<\/dd>\n
\n
\u2022 Verify the fuel pressure on the low pressure side with the operation of the high pressure fuel pump turned off.<\/div>\n<\/dd>\n<\/dl>\n
\u2022 Bleed the remaining pressure in the fuel line using the following procedure.<\/div>\n
\n
\n
1. Switch the ignition off.<\/div>\n
2. Disconnect the high pressure fuel pump connector.<\/div>\n
3. Remove the fuel pump relay. (See RELAY LOCATION [(US)]<\/a>.)<\/div>\n
4. Start the engine and wait until the engine stalls.<\/div>\n<\/dd>\n<\/dl>\n
\u2022 Switch the ignition off.<\/div>\n
\u2022 Install the fuel pump relay.<\/div>\n
\u2022 Switch the ignition ON (engine off).<\/div>\n
\u2022 Display PID FUEL_PRES and simulation item FUEL_PUMP_REQ using the M-MDS. (See PID\/DATA MONITOR INSPECTION<\/a>.) (See SIMULATION INSPECTION<\/a>.)<\/div>\n
\u2022 Turn simulation item FUEL_PUMP_REQ on.<\/div>\n
\u2022 Is the FUEL_PRES PID value 475\u2014555 kPa {4.85\u20145.65 kgf\/cm2<\/sup>, 68.9\u201480.4 psi}<\/span>?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to Troubleshooting Diagnostic Procedure to perform the procedure from Step 2.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to Troubleshooting Diagnostic Procedure to perform the procedure from Step 1.<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n



\n<\/a><\/p>\n

Troubleshooting Diagnostic Procedure<\/p>\n

Intention of troubleshooting procedure<\/div>\n
\u2022 Step 1<\/div>\n
\n
\n
\u2015 Inspect the fuel supply system (low pressure side).<\/div>\n<\/dd>\n<\/dl>\n
\u2022 Step 2<\/div>\n
\n
\n
\u2015 Perform a unit inspection of the fuel pressure sensor.<\/div>\n<\/dd>\n<\/dl>\n
\u2022 Repair completion verification<\/div>\n
\n
\n
\u2015 Verify that the primary malfunction is resolved and there are no other malfunctions.<\/div>\n<\/dd>\n<\/dl>\n

\n\n\n\n\n\n\n\n\n\n\n\n\n
\n

Step<\/p>\n<\/th>\n

\n

Inspection<\/p>\n<\/th>\n

\n

Results<\/p>\n<\/th>\n

\n

Action<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
1<\/div>\n<\/td>\n
\n
PURPOSE: VERIFY IF MALFUNCTION RELATED TO FUEL PIPE (LOW PRESSURE SIDE) AFFECTS DIAGNOSTIC RESULTS<\/div>\n
\u2022 Inspect the fuel pump unit. (See FUEL PUMP UNIT INSPECTION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.) (See FUEL PUMP UNIT INSPECTION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
\u2022 Is there any malfunction?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Replace the fuel pump unit and perform the repair completion verification.<\/div>\n
(See FUEL PUMP UNIT REMOVAL\/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
(See FUEL PUMP UNIT REMOVAL\/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Inspect the fuel system pipes (low to high pressure sides) for fuel leakage and restriction.<\/div>\n
\u2022 If there is any malfunction:<\/div>\n
\n
\n
\u2015 Repair or replace the malfunctioning location and perform the repair completion verification.<\/div>\n<\/dd>\n<\/dl>\n
\u2022 If there is no malfunction:<\/div>\n
\n
\n
\u2015 Go to the next step.<\/div>\n<\/dd>\n<\/dl>\n<\/td>\n<\/tr>\n
\n
2<\/div>\n<\/td>\n
\n
PURPOSE: INSPECT FUEL PRESSURE SENSOR FOR MALFUNCTION<\/div>\n
\u2022 Inspect the applicable part. (See FUEL PRESSURE SENSOR INSPECTION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.) (See FUEL PRESSURE SENSOR INSPECTION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
\u2022 Is the part normal?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Repair or replace the malfunctioning location and perform the repair completion verification.<\/div>\n
(See FUEL INJECTOR REMOVAL\/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
(See FUEL INJECTOR REMOVAL\/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
Repair completion verification 1<\/div>\n<\/td>\n
\n
PURPOSE: VERIFY THAT VEHICLE IS REPAIRED<\/div>\n
\u2022 Install\/connect the part removed\/disconnected during the troubleshooting procedure.<\/div>\n
\u2022 Clear the DTC recorded in the memory. (See CLEARING DTC<\/a>.)<\/div>\n
\u2022 Replicate the vehicle conditions at the time the DTC was detected using the following procedure.<\/div>\n
\n
\n
\u2015 Implement the repeatability verification procedure. (See Repeatability Verification Procedure<\/a>.)<\/div>\n<\/dd>\n<\/dl>\n
\u2022 Perform the DTC inspection for the PCM. (See DTC INSPECTION<\/a>.)<\/div>\n
\u2022 Is the same Pending DTC present?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.<\/div>\n
(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(US)]<\/a>.)<\/div>\n
If the CAN communication is normal, perform the diagnosis from Step 1.<\/div>\n
\u2022 If the malfunction recurs, replace the PCM, then go to the next step. (See PCM REMOVAL\/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.) (See PCM REMOVAL\/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
Repair completion verification 2<\/div>\n<\/td>\n
\n
PURPOSE: VERIFY IF OTHER DTCs DISPLAYED<\/div>\n
\u2022 Perform the DTC inspection. (See DTC INSPECTION<\/a>.)<\/div>\n
\u2022 Are any other DTCs displayed?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair the malfunctioning location according to the applicable DTC troubleshooting.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
DTC troubleshooting completed.<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n
<\/div>\n
<\/div>\n
<\/div>\n

<\/div>\n<\/div>\n","protected":false},"excerpt":{"rendered":"

DTC P0087:00 [PCM (SKYACTIV-G)] SM2334366 id0102t4008200 Note \u2022 To determine the malfunctioning part, proceed with the diagnostics from “Function Inspection Using M-MDS”. Details On DTCs Description Fuel pressure sensor circuit range\/performance problem Detection condition Determination conditions \u2022 If any of the following conditions is met under condition A or condition B: Condition A: \u2015 The actual fuel pressure is lower than the target fuel pressure by 1.2 MPa {12 kgf\/cm2, 174 psi} or more even […]<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_monsterinsights_skip_tracking":false,"_monsterinsights_sitenote_active":false,"_monsterinsights_sitenote_note":"","_monsterinsights_sitenote_category":0,"footnotes":""},"class_list":["post-8822","page","type-page","status-publish","hentry"],"_links":{"self":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages\/8822","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/comments?post=8822"}],"version-history":[{"count":0,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages\/8822\/revisions"}],"wp:attachment":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/media?parent=8822"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}