{"id":8541,"date":"2022-03-10T20:30:40","date_gmt":"2022-03-10T20:30:40","guid":{"rendered":"https:\/\/www.hexorcism.com\/19BP\/sm2333610\/"},"modified":"2022-03-10T20:30:40","modified_gmt":"2022-03-10T20:30:40","slug":"sm2333610","status":"publish","type":"page","link":"https:\/\/www.hexorcism.com\/19BP\/sm2333610\/","title":{"rendered":"INSTALLATION PREPARATIONS"},"content":{"rendered":"
\n

INSTALLATION PREPARATIONS<\/h3>\n<\/div>\n

SM2333610<\/p>\n

<\/p>\n
\n
\n
\n

id000000600400<\/p>\n



\n<\/a><\/p>\n

Rough Cutting of New Parts<\/p>\n

\u2022 For cut and join areas, allow for an overlap of 30\u201450 mm {1.2\u20141.9 in} with the remaining area on the body side and then rough cut the new parts.<\/div>\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3uub00000081<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n



\n<\/a><\/p>\n

Determination of Welding Method<\/p>\n

\u2022 If the total thickness at the area to be welded is 3 mm {0.12 in} or more, use a gas shielded\u2010arc welder to make the plug welds.<\/div>\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3uub00000082<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n



\n<\/a><\/p>\n

Making Holes for Arc Welding<\/p>\n

\u2022 For places that cannot be spot welded, make a hole for arc welding using a punch or drill as follows.<\/div>\n

(mm {IN})<\/p>\n\n\n\n\n\n\n\n\n
\n

Panel thickness (\u03c6)<\/p>\n<\/th>\n

\n

Hole diameter (\u03c6)<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
0.60\u20140.90 {0.024\u20140.035}<\/div>\n<\/td>\n
\n
5.0 {0.20}<\/div>\n<\/td>\n<\/tr>\n
\n
0.91\u20141.20 {0.036\u20140.047}<\/div>\n<\/td>\n
\n
6.0 {0.24}<\/div>\n<\/td>\n<\/tr>\n
\n
1.21\u20141.80 {0.0477\u20140.0708}<\/div>\n<\/td>\n
\n
8.0 {0.31}<\/div>\n<\/td>\n<\/tr>\n
\n
1.81\u20144.50 {0.072\u20140.177}<\/div>\n<\/td>\n
\n
10.0 {0.394}<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
\u2022 Grind the shaded section indicated in the diagram below and create a hole in the part where the 3\u20144 plates are put together. Also, weld the plates together tightly so that gaps do not develop.<\/div>\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3uub00000083<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n



\n<\/a><\/p>\n

Cautions with Ultra-high Strength Steel Sheeting Repairs<\/p>\n

\u2022 Because the ultra high-tensile steel is hard and it may be difficult to reform, when extracting the damaged part using a frame repair machine, perform the work verifying that other parts are not affected.<\/div>\n
\u2022 When drilling welded parts, use a well-ground drill bit.<\/div>\n
\u2022 Perform plug welding (arc welding).Do not perform continuous welding such as cut and join work as it may cause strength degradation.<\/div>\n



\n<\/a><\/p>\n

Application of Weld\u2010through Primer<\/p>\n

\u2022 For treatment against corrosion, remove the paint grease, and other material from the portion of new part and body to be welded, and apply weld\u2010through primer.<\/div>\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
acxuub00000068<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n
<\/div>\n
<\/div>\n
<\/div>\n

<\/div>\n<\/div>\n","protected":false},"excerpt":{"rendered":"

INSTALLATION PREPARATIONS SM2333610 id000000600400 Rough Cutting of New Parts \u2022 For cut and join areas, allow for an overlap of 30\u201450 mm {1.2\u20141.9 in} with the remaining area on the body side and then rough cut the new parts. am3uub00000081 Determination of Welding Method \u2022 If the total thickness at the area to be welded is 3 mm {0.12 in} or more, use a gas shielded\u2010arc welder to make the plug welds. am3uub00000082 Making Holes […]<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_monsterinsights_skip_tracking":false,"_monsterinsights_sitenote_active":false,"_monsterinsights_sitenote_note":"","_monsterinsights_sitenote_category":0,"footnotes":""},"class_list":["post-8541","page","type-page","status-publish","hentry"],"_links":{"self":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages\/8541","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/comments?post=8541"}],"version-history":[{"count":0,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages\/8541\/revisions"}],"wp:attachment":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/media?parent=8541"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}