{"id":10682,"date":"2022-03-10T20:30:58","date_gmt":"2022-03-10T20:30:58","guid":{"rendered":"https:\/\/www.hexorcism.com\/19BP\/sm2841696\/"},"modified":"2022-03-10T20:30:58","modified_gmt":"2022-03-10T20:30:58","slug":"sm2841696","status":"publish","type":"page","link":"https:\/\/www.hexorcism.com\/19BP\/sm2841696\/","title":{"rendered":"TIMING CHAIN DISASSEMBLY"},"content":{"rendered":"
\n

TIMING CHAIN DISASSEMBLY<\/h3>\n<\/div>\n

SM2841696<\/p>\n

<\/p>\n
\n
\n
\n

id011000505500<\/p>\n

Special Service Tool (SST)<\/p>\n\n\n\n
\n
49 E011 1A0<\/div>\n
<\/div>\n
Ring gear brake set<\/div>\n<\/td>\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
\n
\n
Caution<\/div>\n<\/dd>\n
\n
\n
\u2022 If the camshaft is rotated with the timing chain removed and the piston at the top dead center position, the valve may contact the piston and the engine could be damaged. When rotating the camshaft with the timing chain removed, rotate it after lowering the piston from the top dead center position.<\/div>\n
\u2022 When rotating the camshaft using a wrench on the cast hexagon, the wrench may contact the rocker arm and damage the rocker arm. To prevent damage to the rocker arm when holding the camshaft on the cast hexagon, use a wrench on the rear side of the engine as shown in the figure to secure a clearance between the cam.<\/p>\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3uuw00008837<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/dd>\n<\/dl>\n
\n
\n
Note<\/div>\n<\/dd>\n
\n
\u2022 Width at the cast hexagon of the camshaft is 22\u201424 mm {0.87\u20140.94 in}.<\/p>\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
bpe7ze00000032<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/dd>\n<\/dl>\n

1.Disassemble in the order indicated in the table.<\/p>\n

\n\n\n\n
\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
bp28ue00000001<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
\n
1<\/div>\n<\/td>\n
\n
Cylinder head cover<\/div>\n<\/td>\n<\/tr>\n
\n
2<\/div>\n<\/td>\n
\n
Oil shower pipe<\/div>\n<\/td>\n<\/tr>\n
\n
3<\/div>\n<\/td>\n
\n
Spark plug<\/div>\n<\/td>\n<\/tr>\n
\n
4<\/div>\n<\/td>\n
\n
Crankshaft pulley lock bolt<\/div>\n
(See Crankshaft Pulley Lock Bolt Disassembly Note<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
5<\/div>\n<\/td>\n
\n
Crankshaft pulley<\/div>\n<\/td>\n<\/tr>\n
\n
6<\/div>\n<\/td>\n
\n
Oil pan<\/div>\n
(See Oil Pan Disassembly Note<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
7<\/div>\n<\/td>\n
\n
Engine oil level sensor<\/div>\n<\/td>\n<\/tr>\n
\n
8<\/div>\n<\/td>\n
\n
Engine front cover<\/div>\n
(See Engine Front Cover Disassembly Note<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
9<\/div>\n<\/td>\n
\n
Front oil seal<\/div>\n
(See Front Oil Seal Disassembly Note<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
10<\/div>\n<\/td>\n
\n
Chain guide (No.1)<\/div>\n<\/td>\n<\/tr>\n
\n
11<\/div>\n<\/td>\n
\n
Chain tensioner<\/div>\n
(See Chain Tensioner Disassembly Note<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
12<\/div>\n<\/td>\n
\n
Tensioner arm<\/div>\n<\/td>\n<\/tr>\n
\n
13<\/div>\n<\/td>\n
\n
Timing chain<\/div>\n<\/td>\n<\/tr>\n
\n
14<\/div>\n<\/td>\n
\n
Chain guide (No.2)<\/div>\n<\/td>\n<\/tr>\n
\n
15<\/div>\n<\/td>\n
\n
Crankshaft sprocket<\/div>\n<\/td>\n<\/tr>\n
\n
16<\/div>\n<\/td>\n
\n
Oil pump chain tensioner<\/div>\n
(See Oil Pump Chain Disassembly Note<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
17<\/div>\n<\/td>\n
\n
Balancer shaft sprocket<\/div>\n
(See Oil Pump Chain Disassembly Note<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
18<\/div>\n<\/td>\n
\n
Oil pump chain<\/div>\n
(See Oil Pump Chain Disassembly Note<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
19<\/div>\n<\/td>\n
\n
Oil pump driven sprocket<\/div>\n
(See Oil Pump Chain Disassembly Note<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
20<\/div>\n<\/td>\n
\n
Oil pump chain guide<\/div>\n<\/td>\n<\/tr>\n
\n
21<\/div>\n<\/td>\n
\n
Oil pump drive sprocket<\/div>\n<\/td>\n<\/tr>\n
\n
22<\/div>\n<\/td>\n
\n
Key<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n



\n<\/a><\/p>\n

Crankshaft Pulley Lock Bolt Disassembly Note<\/p>\n

1.Hold the crankshaft using the SST<\/span>.<\/p>\n

\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
bpe1ze00000063<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

2.Remove the crankshaft pulley lock bolt.<\/p>\n

\n



\n<\/a><\/p>\n

Oil Pan Disassembly Note<\/p>\n

1.Remove the oil pan using a separator tool.<\/p>\n

\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
adejjw00003946<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n



\n<\/a><\/p>\n

Engine Front Cover Disassembly Note<\/p>\n

1.Remove the engine front cover installation bolts.<\/p>\n

\n

2.Using a screwdriver wrapped in a cloth, peel the sealant away a little at a time, and remove the engine front cover.<\/p>\n

\n

\n
\n
Caution<\/div>\n<\/dd>\n
\n
\n
\u2022 Do not apply excessive force to the screwdriver. Otherwise, the engine front cover could be damaged.<\/div>\n
\u2022 Be careful not to scratch or damage the seal surface. Otherwise, it could cause oil leakage.<\/div>\n<\/div>\n<\/dd>\n<\/dl>\n



\n<\/a><\/p>\n

Front Oil Seal Disassembly Note<\/p>\n

1.Remove the front oil seal using a flathead screwdriver with the tip protected by a clean cloth.<\/p>\n

\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
bpe2ue00000100<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n



\n<\/a><\/p>\n

Chain Tensioner Disassembly Note<\/p>\n

1.Verify the chain tensioner shape and identify the chain tensioner type.<\/p>\n

\n\n\n\n
\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
ac4ccw00002689<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
\n
\n
Note<\/div>\n<\/dd>\n
\n
\u2022 Verifying the chain tensioner type is necessary because the following procedures may differ according to the type of tensioner.<\/div>\n<\/dd>\n<\/dl>\n

2.While moving the exhaust camshaft back and forth in the direction of the arrow using a wrench on the cast hexagon, press down the link plate of the timing chain tensioner using a precision screwdriver and release the plunger lock. (Chain tensioner (type A))<\/p>\n

\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
btstze00000027<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3uuw00008854<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
\n
\n
Note<\/div>\n<\/dd>\n
\n
\u2022 When moving the exhaust camshaft back and forth, the timing chain pushes the plunger in the chain tensioner making it easier to operate the link plate.<\/div>\n<\/dd>\n<\/dl>\n

3.Push back the plunger slowly in the direction shown in the figure with the link plate still pushed down. (Chain tensioner (type A))<\/p>\n

\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3uuw00008855<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

4.Remove the screwdriver from the link plate with the plunger still pushed down. (Chain tensioner (type A))<\/p>\n

\n

5.Release the force slightly from the plunger, and move it back and forth 2\u20143 mm {0.08\u20140.11 in}<\/span>. (Chain tensioner (type A))<\/p>\n

\n

6.Insert a wire with an approx. diameter of 1.5 mm {0.059 in}<\/span> or a paper clip where the link plate hole and the tensioner body hole overlap to secure the link plate and lock the plunger. (Chain tensioner (type A))<\/p>\n

\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3uuw00008856<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

7.Loosen the chain tensioner using the following procedure: (Chain tensioner (type B))<\/p>\n

\n

\n
(1)Insert a metal rod (diameter approx. 1.4 mm {0.055 in}<\/span>, length approx. 55 mm {2.2 in}<\/span>) into the hole in the body of the chain tensioner.<\/dd>\n
\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
bp27ze00000003<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/dd>\n<\/dl>\n
\n
(2)Press the resister ring and unlock the plunger.<\/dd>\n
\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
bp27ze00000004<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/dd>\n<\/dl>\n
\n
(3)Press the timing chain in the direction of the arrow and press in the chain tensioner plunger to the position where the groove and body hole are aligned.<\/dd>\n
\n\n\n\n
\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
amxuuw00004405<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/dd>\n<\/dl>\n
\n
(4)With the plunger pressed in, further insert the metal rod set in (1) above.<\/dd>\n
\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
bp27ze00000005<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
\n
\n
Note<\/div>\n<\/dd>\n
\n
\u2022 The rod secures the plunger and releases the tension.<\/div>\n<\/dd>\n<\/dl>\n<\/dd>\n<\/dl>\n
\n
(5)Loosen the power of the hand pressing the plunger and verify that the pressed-in rod does not move.<\/dd>\n
<\/dd>\n<\/dl>\n

8.Remove the chain tensioner.<\/p>\n

\n



\n<\/a><\/p>\n

Oil Pump Chain Disassembly Note<\/p>\n

1.Hold the crankshaft using the SST<\/span>.<\/p>\n

\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
bpe1ze00000095<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

2.Slightly loosen the balancer shaft sprocket and oil pump driven sprocket installation bolts.<\/p>\n

\n

\n
\n
Note<\/div>\n<\/dd>\n
\n
\u2022 At this stage, only loosen the installation bolts, do not remove it. Remove the bolt after removing the oil pump chain tensioner.<\/div>\n<\/dd>\n<\/dl>\n

3.Set a cloth wrapped flathead screwdriver in the gap between oil pump drive sprocket and the oil pump chain as shown in the figure.<\/p>\n

\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
ac5wzw00010912<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

4.Move the screwdriver in the direction of the arrow and press the oil pump chain, and then press in the plunger of the oil pump chain tensioner.<\/p>\n

\n\n\n\n
\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
ac5wzw00010913<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

5.Insert a wire with an approx. diameter of 1.4 mm {0.055 in} or a paper clip into the body hole of the oil pump chain tensioner with the plunger pressed.<\/p>\n

\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
btstze00000028<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
\n
\n
Note<\/div>\n<\/dd>\n
\n
\u2022 The wire or paper clip secures the plunger, and the tension can be released.<\/div>\n<\/dd>\n<\/dl>\n

6.Remove the oil pump chain tensioner.<\/p>\n

\n

7.Remove the oil pump chain and balancer shaft sprocket as a single unit.<\/p>\n

\n

8.Remove the oil pump driven sprocket.<\/p>\n

\n<\/div>\n

<\/div>\n
<\/div>\n
<\/div>\n

<\/div>\n<\/div>\n","protected":false},"excerpt":{"rendered":"

TIMING CHAIN DISASSEMBLY SM2841696 id011000505500 Special Service Tool (SST) 49 E011 1A0 Ring gear brake set Caution \u2022 If the camshaft is rotated with the timing chain removed and the piston at the top dead center position, the valve may contact the piston and the engine could be damaged. When rotating the camshaft with the timing chain removed, rotate it after lowering the piston from the top dead center position. \u2022 When rotating the camshaft […]<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_monsterinsights_skip_tracking":false,"_monsterinsights_sitenote_active":false,"_monsterinsights_sitenote_note":"","_monsterinsights_sitenote_category":0,"footnotes":""},"class_list":["post-10682","page","type-page","status-publish","hentry"],"_links":{"self":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages\/10682","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/comments?post=10682"}],"version-history":[{"count":0,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages\/10682\/revisions"}],"wp:attachment":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/media?parent=10682"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}