{"id":10517,"date":"2022-03-10T20:30:57","date_gmt":"2022-03-10T20:30:57","guid":{"rendered":"https:\/\/www.hexorcism.com\/19BP\/sm2566554\/"},"modified":"2022-03-10T20:30:57","modified_gmt":"2022-03-10T20:30:57","slug":"sm2566554","status":"publish","type":"page","link":"https:\/\/www.hexorcism.com\/19BP\/sm2566554\/","title":{"rendered":"CONFIGURATION"},"content":{"rendered":"
\n

CONFIGURATION<\/h3>\n<\/div>\n

SM2566554<\/p>\n

<\/p>\n
\n
\n
\n

id990200001100<\/p>\n

\n
\n
Note<\/div>\n<\/dd>\n
\n
\n
\u2022 If the configuration is performed, the set values for the personalization features may be reset to the initial values (condition when shipped from factory). Verify the set values for the personalization features with the customer before performing the configuration and perform the personalization features setting after performing the configuration.<\/div>\n
\u2022 There are two types of configurations, one which writes As-Built data to the module and the other which reads data from the old module and writes the data to the new module.<\/div>\n
\u2022 When performing configuration on a module supporting read\/write, perform the configuration before removing the old module because it is necessary to read data from the old module. (See Module Table<\/a>.)<\/div>\n<\/div>\n<\/dd>\n<\/dl>\n

1.Connect the M-MDS to the DLC-2.<\/p>\n

\n

2.Switch the ignition ON (engine off or on).<\/p>\n

\n

3.Perform the vehicle identification.<\/p>\n

\n

4.Select the following items from the initialization screen of the M-MDS.<\/p>\n

\n

\n
(1)”Toolbox”<\/dd>\n
<\/dd>\n<\/dl>\n
\n
(2)”Work Support”<\/dd>\n
<\/dd>\n<\/dl>\n
\n
(3)”Configuration”<\/dd>\n
<\/dd>\n<\/dl>\n

5.Select the applicable module according to the module table. (See Module Table<\/a>.)<\/p>\n

\n

6.Perform the configuration following the instructions on the screen.<\/p>\n

\n

\n
\n
Caution<\/div>\n<\/dd>\n
\n
\u2022 When performing the configuration, CAN communication is cut temporarily and communication error DTCs may be detected. After performing the configuration, perform the DTC inspection and clear DTCs if any are displayed.<\/div>\n<\/dd>\n<\/dl>\n

7.Perform the DTC inspection. (See DTC INSPECTION<\/a>.)<\/p>\n

\n

\n
\n
\u2022 If a DTC is displayed, clear it. (See CLEARING DTC<\/a>.)<\/div>\n
\n
\n
\u2015 If the DTC is displayed again, repair the malfunctioning location according to the applicable DTC troubleshooting.<\/div>\n<\/dd>\n<\/dl>\n<\/dd>\n<\/dl>\n



\n<\/a><\/p>\n

Module Table<\/p>\n

\n

\u00d7: Applicable\u2014: Not applicable<\/p>\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
\n

M-MDS display name<\/p>\n<\/th>\n

\n

Applicable module<\/p>\n<\/th>\n

\n

Write As-Built data<\/p>\n<\/th>\n

\n

Read\/write data<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
ADD<\/div>\n<\/td>\n
\n
Active driving display<\/div>\n<\/td>\n
\n
\u00d7<\/div>\n<\/td>\n
\n
\u2014<\/div>\n<\/td>\n<\/tr>\n
\n
BCM<\/div>\n<\/td>\n
\n
Body control module (BCM)<\/div>\n<\/td>\n
\n
\u00d7<\/div>\n<\/td>\n
\n
\u00d7<\/div>\n<\/td>\n<\/tr>\n
\n
CCU<\/div>\n<\/td>\n
\n
Climate control unit<\/div>\n<\/td>\n
\n
\u00d7<\/div>\n<\/td>\n
\n
\u2014<\/div>\n<\/td>\n<\/tr>\n
\n
DASH_ESU<\/div>\n<\/td>\n
\n
Dash-electrical supply unit<\/div>\n<\/td>\n
\n
\u00d7<\/div>\n<\/td>\n
\n
\u2014<\/div>\n<\/td>\n<\/tr>\n
\n
DSC<\/div>\n<\/td>\n
\n
DSC HU\/CM<\/div>\n<\/td>\n
\n
\u00d7<\/div>\n<\/td>\n
\n
\u2014<\/div>\n<\/td>\n<\/tr>\n
\n
Electronically controlled brake unit<\/div>\n<\/td>\n<\/tr>\n
\n
ESU<\/div>\n<\/td>\n
\n
Electrical supply unit (ESU)<\/div>\n<\/td>\n
\n
\u00d7<\/div>\n<\/td>\n
\n
\u2014<\/div>\n<\/td>\n<\/tr>\n
\n
IC<\/div>\n<\/td>\n
\n
Instrument cluster<\/div>\n<\/td>\n
\n
\u00d7<\/div>\n<\/td>\n
\n
\u2014<\/div>\n<\/td>\n<\/tr>\n
\n
LFU<\/div>\n<\/td>\n
\n
LF control unit<\/div>\n<\/td>\n
\n
\u00d7<\/div>\n<\/td>\n
\n
\u2014<\/div>\n<\/td>\n<\/tr>\n
\n
PCM<\/div>\n<\/td>\n
\n
PCM<\/div>\n<\/td>\n
\n
\u00d7<\/div>\n<\/td>\n
\n
\u00d7<\/div>\n<\/td>\n<\/tr>\n
\n
SAS<\/div>\n<\/td>\n
\n
SAS control module<\/div>\n<\/td>\n
\n
\u2014<\/div>\n<\/td>\n
\n
\u00d7<\/div>\n<\/td>\n<\/tr>\n
\n
TCM<\/div>\n<\/td>\n
\n
TCM<\/div>\n<\/td>\n
\n
\u00d7<\/div>\n<\/td>\n
\n
\u2014<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n
<\/div>\n
<\/div>\n
<\/div>\n

<\/div>\n<\/div>\n","protected":false},"excerpt":{"rendered":"

CONFIGURATION SM2566554 id990200001100 Note \u2022 If the configuration is performed, the set values for the personalization features may be reset to the initial values (condition when shipped from factory). Verify the set values for the personalization features with the customer before performing the configuration and perform the personalization features setting after performing the configuration. \u2022 There are two types of configurations, one which writes As-Built data to the module and the other which reads data […]<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_monsterinsights_skip_tracking":false,"_monsterinsights_sitenote_active":false,"_monsterinsights_sitenote_note":"","_monsterinsights_sitenote_category":0,"footnotes":""},"class_list":["post-10517","page","type-page","status-publish","hentry"],"_links":{"self":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages\/10517","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/comments?post=10517"}],"version-history":[{"count":0,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages\/10517\/revisions"}],"wp:attachment":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/media?parent=10517"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}