{"id":10481,"date":"2022-03-10T20:30:57","date_gmt":"2022-03-10T20:30:57","guid":{"rendered":"https:\/\/www.hexorcism.com\/19BP\/sm2566458\/"},"modified":"2022-03-10T20:30:57","modified_gmt":"2022-03-10T20:30:57","slug":"sm2566458","status":"publish","type":"page","link":"https:\/\/www.hexorcism.com\/19BP\/sm2566458\/","title":{"rendered":"DETERMINING SHORT BETWEEN CIRCUITS LOCATION (CAN-BUS No.4) [(US)]"},"content":{"rendered":"
\n

DETERMINING SHORT BETWEEN CIRCUITS LOCATION (CAN-BUS No.4) [(US)]<\/h3>\n<\/div>\n

SM2566458<\/p>\n

<\/p>\n
\n
\n
\n

id1002x1003200<\/p>\n

\n
\n
Caution<\/div>\n<\/dd>\n
\n
\u2022 Perform the following malfunction diagnosis only when it is diagnosed with a short to ground by CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(US)]<\/a>.)<\/div>\n<\/dd>\n<\/dl>\n



\n<\/a><\/p>\n

System Wiring Diagram<\/p>\n\n\n\n
\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00034237<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n



\n<\/a><\/p>\n

Determination Procedure<\/p>\n

\n
\n
Caution<\/div>\n<\/dd>\n
\n
\n
\u2022 When disconnecting the connector, verify that there is no looseness, damage, deformation, corrosion, or poor connection of the connector terminals.<\/div>\n
\u2022 When inspecting the connector, touch it with a paper clip or similar thin pin without directly inserting a tester probe into the terminal.<\/div>\n
\u2022 Disconnect the negative battery cable before performing any work that requires handling of connectors.<\/div>\n<\/div>\n<\/dd>\n<\/dl>\n

\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
\n

Step<\/p>\n<\/th>\n

\n

Inspection<\/p>\n<\/th>\n

\n

Action<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
1<\/div>\n<\/td>\n
\n
INSPECT BODY CONTROL MODULE (BCM) FOR SHORT BETWEEN CIRCUITS<\/div>\n
\u2022 Switch the ignition off.<\/div>\n
\u2022 Disconnect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Disconnect the connector 2 which has body control module (BCM) terminals 2D and 2B.<\/div>\n
\u2022 Connect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Switch the ignition ON (engine off).<\/div>\n
\u2022 Measure the voltage at body control module (BCM) terminals 2D and 2B (wiring harness side).<\/div>\n
\u2022 Is the voltage at body control module (BCM) terminals 2D and 2B (wiring harness side) the same?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Replace the body control module (BCM) because there is a short between circuits in the body control module (BCM).<\/div>\n
(See BODY CONTROL MODULE (BCM) REMOVAL\/INSTALLATION<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
2<\/div>\n<\/td>\n
\n
INSPECT CAN LINE BETWEEN CONNECTOR C-08 AND BODY CONTROL MODULE (BCM) FOR SHORT BETWEEN CIRCUITS<\/div>\n
\u2022 Switch the ignition off.<\/div>\n
\u2022 Disconnect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Disconnect the connector C-08.<\/div>\n
\u2022 Connect the connector 2 which has body control module (BCM) terminals 2D and 2B.<\/div>\n
\u2022 Connect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Switch the ignition ON (engine off).<\/div>\n
\u2022 Measure the voltage at body control module (BCM) terminals 2D and 2B.<\/div>\n
\u2022 Is the voltage at body control module (BCM) terminals 2D and 2B the same?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair or replace the wiring harness between the body control module (BCM) and connector C-08 because the wiring harness is shorted between circuits.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
3<\/div>\n<\/td>\n
\n
INSPECT CAN LINE BETWEEN CONNECTOR C-59\/C-69 AND CONNECTOR C-08 FOR SHORT BETWEEN CIRCUITS<\/div>\n
\u2022 Switch the ignition off.<\/div>\n
\u2022 Disconnect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Disconnect the connector C-59.(4SD)<\/div>\n
\u2022 Disconnect the connector C-69.(5HB)<\/div>\n
\u2022 Connect the connector C-08.<\/div>\n
\u2022 Connect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Switch the ignition ON (engine off).<\/div>\n
\u2022 Measure the voltage at body control module (BCM) terminals 2D and 2B.<\/div>\n
\u2022 Is the voltage at body control module (BCM) terminals 2D and 2B the same?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair or replace the wiring harness between connector C-59\/C-69 and connector C-08 because the wiring harness is shorted between circuits.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
4<\/div>\n<\/td>\n
\n
INSPECT CAN LINE BETWEEN ELECTRICAL SUPPLY UNIT (ESU) AND CONNECTOR C-59\/C-69 FOR SHORT BETWEEN CIRCUITS<\/div>\n
\u2022 Measure the voltage at electrical supply unit (ESU) terminals 1X and 1W.<\/div>\n
\u2022 Is the voltage at electrical supply unit (ESU) terminals 1X and 1W the same?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to Step 6. (with parking sensor system)<\/div>\n
Go to Step 11. (5HB (without parking sensor system))<\/div>\n
Go to Step 14. (4SD (without parking sensor system))<\/div>\n<\/td>\n<\/tr>\n
\n
5<\/div>\n<\/td>\n
\n
INSPECT ELECTRICAL SUPPLY UNIT (ESU) FOR SHORT BETWEEN CIRCUITS<\/div>\n
\u2022 Switch the ignition off.<\/div>\n
\u2022 Disconnect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Connect the connector C-59.(4SD)<\/div>\n
\u2022 Connect the connector C-69.(5HB)<\/div>\n
\u2022 Disconnect the electrical supply unit (ESU) connector.<\/div>\n
\u2022 Connect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Switch the ignition ON (engine off).<\/div>\n
\u2022 Measure the voltage at body control module (BCM) terminals 2D and 2B.<\/div>\n
\u2022 Is the voltage at body control module (BCM) terminals 2D and 2B the same?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair or replace the wiring harness between the electrical supply unit (ESU) and connector C-59\/C-69 because the wiring harness is shorted between circuits.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Replace the electrical supply unit (ESU) because there is a short between circuits in the electrical supply unit (ESU).<\/div>\n
(See ELECTRICAL SUPPLY UNIT (ESU) REMOVAL\/INSTALLATION<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
6<\/div>\n<\/td>\n
\n
INSPECT CAN LINE BETWEEN CONNECTOR C-58 AND CONNECTOR C-59\/C-69 FOR SHORT BETWEEN CIRCUITS<\/div>\n
\u2022 Switch the ignition off.<\/div>\n
\u2022 Disconnect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Connect the connector C-59.(4SD)<\/div>\n
\u2022 Connect the connector C-69.(5HB)<\/div>\n
\u2022 Disconnect the connector C-58.<\/div>\n
\u2022 Connect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Switch the ignition ON (engine off).<\/div>\n
\u2022 Measure the voltage at body control module (BCM) terminals 2D and 2B.<\/div>\n
\u2022 Is the voltage at body control module (BCM) terminals 2D and 2B the same?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair or replace the wiring harness between connector C-58 and connector C-59\/C-69 because the wiring harness is shorted between circuits.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
7<\/div>\n<\/td>\n
\n
INSPECT BETWEEN PARKING ASSIST UNIT (ULTRASONIC) AND CONNECTOR C-58 FOR SHORT BETWEEN CIRCUITS<\/div>\n
\u2022 Switch the ignition off.<\/div>\n
\u2022 Disconnect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Inspect for continuity between parking assist unit (ultrasonic) terminals 1X and 1Z.<\/div>\n
\u2022 Is there continuity?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to Step 9.<\/div>\n<\/td>\n<\/tr>\n
\n
8<\/div>\n<\/td>\n
\n
INSPECT PARKING ASSIST UNIT (ULTRASONIC) FOR SHORT BETWEEN CIRCUITS<\/div>\n
\u2022 Disconnect the parking assist unit (ultrasonic) connector.<\/div>\n
\u2022 Inspect for continuity between parking assist unit (ultrasonic) terminals 1X and 1Z (wiring harness side).<\/div>\n
\u2022 Is there continuity?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair or replace the wiring harness between the parking assist unit (ultrasonic) and connector C-58 because the wiring harness is shorted between circuits.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Replace the parking assist unit (ultrasonic) because there is a short between circuits in the parking assist unit (ultrasonic).<\/div>\n
(See PARKING ASSIST UNIT (ULTRASONIC) REMOVAL\/INSTALLATION<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
9<\/div>\n<\/td>\n
\n
INSPECT BETWEEN REAR SIDE RADAR SENSOR (RH) AND CONNECTOR C-60\/C-70 FOR SHORT BETWEEN CIRCUITS<\/div>\n
\u2022 Connect the connector C-58.<\/div>\n
\u2022 Disconnect the connector C-60.(4SD)<\/div>\n
\u2022 Disconnect the connector C-70.(5HB)<\/div>\n
\u2022 Connect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Switch the ignition ON (engine off).<\/div>\n
\u2022 Measure the voltage at body control module (BCM) terminals 2D and 2B.<\/div>\n
\u2022 Is the voltage at body control module (BCM) terminals 2D and 2B the same?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair or replace the wiring harness between the connector C-60\/C-70 and connector C-58 because the wiring harness is shorted between circuits.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
10<\/div>\n<\/td>\n
\n
INSPECT REAR SIDE RADAR SENSOR (RH) FOR SHORT BETWEEN CIRCUITS<\/div>\n
\u2022 Switch the ignition off.<\/div>\n
\u2022 Disconnect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Disconnect the rear side radar sensor (RH) connector.<\/div>\n
\u2022 Inspect for continuity between rear side radar sensor (RH) terminals C and D (wiring harness side).<\/div>\n
\u2022 Is there continuity?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair or replace the wiring harness between the rear side radar sensor (RH) and connector C-60\/C-70 because the wiring harness is shorted between circuits.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Replace the rear side radar sensor (RH) because there is a short between circuits in the rear side radar sensor (RH).<\/div>\n
(See REAR SIDE RADAR SENSOR REMOVAL\/INSTALLATION<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
11<\/div>\n<\/td>\n
\n
INSPECT CAN LINE BETWEEN CONNECTOR C-68 AND CONNECTOR C-69 FOR SHORT BETWEEN CIRCUITS<\/div>\n
\u2022 Switch the ignition off.<\/div>\n
\u2022 Disconnect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Connect the connector C-69.<\/div>\n
\u2022 Disconnect the connector C-68.<\/div>\n
\u2022 Connect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Switch the ignition ON (engine off).<\/div>\n
\u2022 Measure the voltage at body control module (BCM) terminals 2D and 2B.<\/div>\n
\u2022 Is the voltage at body control module (BCM) terminals 2D and 2B the same?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair or replace the wiring harness between connector C-68 and connector C-69 because the wiring harness is shorted between circuits.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
12<\/div>\n<\/td>\n
\n
INSPECT CAN LINE BETWEEN CONNECTOR C-70 AND CONNECTOR C-68 FOR SHORT BETWEEN CIRCUITS<\/div>\n
\u2022 Switch the ignition off.<\/div>\n
\u2022 Disconnect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Disconnect the connector C-70.<\/div>\n
\u2022 Connect the connector C-68<\/div>\n
\u2022 Connect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Switch the ignition ON (engine off).<\/div>\n
\u2022 Measure the voltage at body control module (BCM) terminals 2D and 2B.<\/div>\n
\u2022 Is the voltage at body control module (BCM) terminals 2D and 2B the same?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair or replace the wiring harness between the connector C-70 and connector C-68 because the wiring harness is shorted between circuits.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
13<\/div>\n<\/td>\n
\n
INSPECT REAR SIDE RADAR SENSOR (RH) FOR SHORT BETWEEN CIRCUITS<\/div>\n
\u2022 Switch the ignition off.<\/div>\n
\u2022 Disconnect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Disconnect the rear side radar sensor (RH) connector.<\/div>\n
\u2022 Inspect for continuity between rear side radar sensor (RH) terminals C and D (wiring harness side).<\/div>\n
\u2022 Is there continuity?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair or replace the wiring harness between the rear side radar sensor (RH) and connector C-70 because the wiring harness is shorted between circuits.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Replace the rear side radar sensor (RH) because there is a short between circuits in the rear side radar sensor (RH).<\/div>\n
(See REAR SIDE RADAR SENSOR REMOVAL\/INSTALLATION<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
14<\/div>\n<\/td>\n
\n
INSPECT CAN LINE BETWEEN CONNECTOR C-66 AND CONNECTOR C-59 FOR SHORT BETWEEN CIRCUITS<\/div>\n
\u2022 Switch the ignition off.<\/div>\n
\u2022 Disconnect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Connect the connector C-59.<\/div>\n
\u2022 Disconnect the connector C-66.<\/div>\n
\u2022 Connect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Switch the ignition ON (engine off).<\/div>\n
\u2022 Measure the voltage at body control module (BCM) terminals 2D and 2B.<\/div>\n
\u2022 Is the voltage at body control module (BCM) terminals 2D and 2B the same?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair or replace the wiring harness between connector C-66 and connector C-59 because the wiring harness is shorted between circuits.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
15<\/div>\n<\/td>\n
\n
INSPECT JB No.3 FOR SHORT BETWEEN CIRCUITS<\/div>\n
\u2022 Switch the ignition off.<\/div>\n
\u2022 Disconnect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Connect the connector C-66.<\/div>\n
\u2022 Disconnect the connector C-67.<\/div>\n
\u2022 Connect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Switch the ignition ON (engine off).<\/div>\n
\u2022 Measure the voltage at body control module (BCM) terminals 2D and 2B.<\/div>\n
\u2022 Is the voltage at body control module (BCM) terminals 2D and 2B the same?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Replace the JB No.3 because there is a short between circuits in the JB No.3.<\/div>\n<\/td>\n<\/tr>\n
\n
16<\/div>\n<\/td>\n
\n
INSPECT CAN LINE BETWEEN CONNECTOR C-60 AND CONNECTOR C-67 FOR SHORT BETWEEN CIRCUITS<\/div>\n
\u2022 Switch the ignition off.<\/div>\n
\u2022 Disconnect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Disconnect the connector C-60.<\/div>\n
\u2022 Connect the connector C-67<\/div>\n
\u2022 Connect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Switch the ignition ON (engine off).<\/div>\n
\u2022 Measure the voltage at body control module (BCM) terminals 2D and 2B.<\/div>\n
\u2022 Is the voltage at body control module (BCM) terminals 2D and 2B the same?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair or replace the wiring harness between connector C-60 and connector C-67 because the wiring harness is shorted between circuits.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
17<\/div>\n<\/td>\n
\n
INSPECT REAR SIDE RADAR SENSOR (RH) FOR SHORT BETWEEN CIRCUITS<\/div>\n
\u2022 Switch the ignition off.<\/div>\n
\u2022 Disconnect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION\/CONNECTION [(US)]<\/a>.)<\/div>\n
\u2022 Disconnect the rear side radar sensor (RH) connector.<\/div>\n
\u2022 Inspect for continuity between rear side radar sensor (RH) terminals C and D (wiring harness side).<\/div>\n
\u2022 Is there continuity?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair or replace the wiring harness between the rear side radar sensor (RH) and connector C-60 because the wiring harness is shorted between circuits.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Replace the rear side radar sensor (RH) because there is a short between circuits in the rear side radar sensor (RH).<\/div>\n
(See REAR SIDE RADAR SENSOR REMOVAL\/INSTALLATION<\/a>.)<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n
<\/div>\n
<\/div>\n
<\/div>\n

<\/div>\n<\/div>\n","protected":false},"excerpt":{"rendered":"

DETERMINING SHORT BETWEEN CIRCUITS LOCATION (CAN-BUS No.4) [(US)] SM2566458 id1002x1003200 Caution \u2022 Perform the following malfunction diagnosis only when it is diagnosed with a short to ground by CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(US)].) System Wiring Diagram am3zzw00034237 Determination Procedure Caution \u2022 When disconnecting the connector, verify that there is no looseness, damage, deformation, corrosion, or poor connection of the connector terminals. \u2022 When inspecting […]<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_monsterinsights_skip_tracking":false,"_monsterinsights_sitenote_active":false,"_monsterinsights_sitenote_note":"","_monsterinsights_sitenote_category":0,"footnotes":""},"class_list":["post-10481","page","type-page","status-publish","hentry"],"_links":{"self":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages\/10481","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/comments?post=10481"}],"version-history":[{"count":0,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages\/10481\/revisions"}],"wp:attachment":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/media?parent=10481"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}