{"id":10250,"date":"2022-03-10T20:30:54","date_gmt":"2022-03-10T20:30:54","guid":{"rendered":"https:\/\/www.hexorcism.com\/19BP\/sm2565973\/"},"modified":"2022-03-10T20:30:54","modified_gmt":"2022-03-10T20:30:54","slug":"sm2565973","status":"publish","type":"page","link":"https:\/\/www.hexorcism.com\/19BP\/sm2565973\/","title":{"rendered":"BRAKE FLUID AIR BLEEDING [(US)]"},"content":{"rendered":"
\n

BRAKE FLUID AIR BLEEDING [(US)]<\/h3>\n<\/div>\n

SM2565973<\/p>\n

<\/p>\n
\n
\n
\n

id041100815398<\/p>\n

Oil and Chemical Type<\/p>\n\n\n\n
\n
Brake fluid type<\/div>\n
<\/div>\n
Type: SAE J1703 or FMVSS116 DOT-3<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
\n
\n
Caution<\/div>\n<\/dd>\n
\n
\n
\u2022 Brake fluid will damage painted surfaces. Be careful not to spill any on painted surfaces. In addition, if there is any brake fluid on the wiring harness, the wire insulation may corrode causing a malfunction such as a short circuit. If brake fluid gets on a painted surface or wiring harness, wash and flush it off completely with water immediately.<\/div>\n
\u2022 Do not empty the brake fluid in the rear brake caliper. Otherwise, the DSC HU\/CM could be damaged.<\/div>\n
\u2022 A new rear brake caliper has been plugged sealing off the brake fluid. For this reason, remove the plug of the rear brake caliper directly before installing the rear brake caliper to the vehicle. Other than for this, do not remove the plug of the rear brake caliper.<\/div>\n
\u2022 When disconnecting the brake hose from the rear brake caliper, always plug and seal the rear brake caliper so that brake fluid does not leak.<\/div>\n<\/div>\n<\/dd>\n<\/dl>\n
\n
\n
Note<\/div>\n<\/dd>\n
\n
\n
\u2022 Keep the fluid level in the brake fluid reserve tank at 3\/4 full or more during the air bleeding.<\/div>\n
\u2022 Bleed the air from the brake caliper that is the nearest to the master cylinder.<\/div>\n<\/div>\n<\/dd>\n<\/dl>\n
\n\n\n\n\n\n
\n

Brake fluid type<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
SAE J1703 or FMVSS116 DOT-3<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n

1.Switch the ignition ON (engine off).<\/p>\n

\n

2.Release the electric parking brake.<\/p>\n

\n

3.Switch the ignition OFF while pressing the electric parking brake switch.<\/p>\n

\n

4.Remove the cap from the brake fluid reserved tank and add brake fluid.<\/p>\n

\n

5.Remove the bleeder cap on the brake caliper, and attach a vinyl tube to the bleeder screw.<\/p>\n

\n

6.Place the other end of the vinyl tube in a clear container and fill the container with fluid during air bleeding.<\/p>\n

\n

\n
\n
Note<\/div>\n<\/dd>\n
\n
\u2022 Air bleeding from the brake pipe can be implemented quickly by slowly depressing the brake pedal.<\/div>\n<\/dd>\n<\/dl>\n

7.Working with two people, one should pump the brake pedal strongly and quickly several times, and then depress and hold the pedal down.<\/p>\n

\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
ac4ccw00001649<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

8.While the brake pedal is depressed, the other should loosen the bleeder screw using a commercially available flare nut wrench, drain out any fluid containing air bubbles, and tighten the bleeder screw.<\/p>\n

\n\n\n\n
<\/td>\n\n\n\n\n
<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
am3zzw00031282<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

9.Repeat Steps 7 and 8 until no air bubbles are seen.<\/p>\n

\n

10.Perform air bleeding as described in the above procedures for all brake calipers.<\/p>\n

\n

\n
\n
Note<\/div>\n<\/dd>\n
\n
\u2022 If the air bleed from the left\/right rear calipers is insufficient, air bleeding can implemented quickly by operating\/releasing the electric parking brake several times while performing the work in Steps 7 and 8.<\/div>\n<\/dd>\n<\/dl>\n

11.Clean the brake calipers.<\/p>\n

\n

12.After air bleeding, inspect the following:<\/p>\n

\n

\n
\n
\u2022 Brake operation<\/div>\n
\u2022 Fluid leakage<\/div>\n
\u2022 Fluid level<\/div>\n<\/dd>\n<\/dl>\n<\/div>\n
<\/div>\n
<\/div>\n
<\/div>\n

<\/div>\n<\/div>\n","protected":false},"excerpt":{"rendered":"

BRAKE FLUID AIR BLEEDING [(US)] SM2565973 id041100815398 Oil and Chemical Type Brake fluid type Type: SAE J1703 or FMVSS116 DOT-3 Caution \u2022 Brake fluid will damage painted surfaces. Be careful not to spill any on painted surfaces. In addition, if there is any brake fluid on the wiring harness, the wire insulation may corrode causing a malfunction such as a short circuit. If brake fluid gets on a painted surface or wiring harness, wash and […]<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_monsterinsights_skip_tracking":false,"_monsterinsights_sitenote_active":false,"_monsterinsights_sitenote_note":"","_monsterinsights_sitenote_category":0,"footnotes":""},"class_list":["post-10250","page","type-page","status-publish","hentry"],"_links":{"self":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages\/10250","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/comments?post=10250"}],"version-history":[{"count":0,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages\/10250\/revisions"}],"wp:attachment":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/media?parent=10250"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}