{"id":10029,"date":"2022-03-10T20:30:53","date_gmt":"2022-03-10T20:30:53","guid":{"rendered":"https:\/\/www.hexorcism.com\/19BP\/sm2565584\/"},"modified":"2022-03-10T20:30:53","modified_gmt":"2022-03-10T20:30:53","slug":"sm2565584","status":"publish","type":"page","link":"https:\/\/www.hexorcism.com\/19BP\/sm2565584\/","title":{"rendered":"FAST IDLE\/RUNS ON [SKYACTIV-G (US)]"},"content":{"rendered":"
\n

FAST IDLE\/RUNS ON [SKYACTIV-G (US)]<\/h3>\n<\/div>\n

SM2565584<\/p>\n

<\/p>\n
\n
\n
\n

id0103s48896s6<\/p>\n

\n\n\n\n\n\n\n\n\n
\n

Troubleshooting item<\/p>\n<\/th>\n

\n

Fast idle\/runs on<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
Description<\/span><\/div>\n<\/td>\n
\n
\u2022 Engine speed continues at fast idle after warm-up.<\/div>\n
\u2022 Engine runs after ignition is switched off.<\/div>\n<\/td>\n<\/tr>\n
\n
Possible cause<\/span><\/div>\n<\/td>\n
\n
\u2022 Cooling system malfunction<\/div>\n
\u2022 PCM DTC is stored<\/div>\n
\u2022 Accelerator pedal stuck depressed<\/div>\n
\u2022 Erratic signal to PCM<\/div>\n
\n
\n
\u2015 APP sensor or related circuit malfunction<\/div>\n
\u2015 Clutch stroke sensor or related circuit malfunction (MTX)<\/div>\n
\u2015 Communication error between TCM and PCM (ATX)<\/div>\n
\u2015 ECT sensor No.1 or related circuit malfunction<\/div>\n
\u2015 ECT sensor No.2 or related circuit malfunction<\/div>\n
\u2015 A\/F sensor or related circuit malfunction<\/div>\n
\u2015 HO2S or related circuit malfunction<\/div>\n<\/dd>\n<\/dl>\n
\u2022 Improper load signal input<\/div>\n
\n
\n
\u2015 Improper A\/C request signal<\/div>\n<\/dd>\n<\/dl>\n
\u2022 Improper operation of drive-by-wire control system<\/div>\n
\u2022 Throttle body malfunction<\/div>\n
\u2022 Fuel injector malfunction<\/div>\n
\u2022 Spill valve control solenoid valve malfunction (built-into high pressure fuel pump)<\/div>\n
\u2022 Air leakage from intake-air system<\/div>\n
\u2022 Injector driver (built-into PCM) malfunction<\/div>\n
\n
\n
Warning<\/div>\n<\/dd>\n
\n
\n
\u2022 The following troubleshooting flow chart contains the fuel system diagnosis and repair procedures. Read the following warnings before performing the fuel system services:<\/div>\n
\n
\n
\u2015 Fuel vapor is hazardous. It can easily ignite, causing serious injury and damage. Always keep sparks and flames away from fuel.<\/div>\n
\u2015 Highly pressurized fuel may spray out if the fuel line is cut. Due to the following dangers occurring with a fuel spray, always complete the \u201cFuel Line Safety Procedure\u201d to prevent the fuel from spraying. (See BEFORE SERVICE PRECAUTION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.) (See BEFORE SERVICE PRECAUTION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
\n
\n
\u2022 Fuel may cause irritation if it comes in contact with skin and eyes.<\/div>\n
\u2022 If fuel ignites and causes a fire, it may lead to serious injury or death, and damage to property and facilities.<\/div>\n<\/dd>\n<\/dl>\n
\u2015 Fuel is highly flammable and dangerous. Fuel line spills and leakage can cause serious injury or death, and damage to equipment. Always refer to the \u201cQuick Release Connector Removal\/Installation (fuel system)\u201d before performing the fuel hose installation, and execute the \u201cFuel Leakage Inspection\u201d after installation. (See QUICK RELEASE CONNECTOR (FUEL SYSTEM) REMOVAL\/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.) (See QUICK RELEASE CONNECTOR (FUEL SYSTEM) REMOVAL\/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.) (See AFTER SERVICE PRECAUTION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.) (See AFTER SERVICE PRECAUTION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n<\/dd>\n<\/dl>\n<\/div>\n<\/dd>\n<\/dl>\n
\n
\n
Caution<\/div>\n<\/dd>\n
\n
\u2022 Disconnecting\/connecting the quick release connector without cleaning it may possibly cause damage to the fuel pipe and quick release connector. Always clean the quick release connector joint area before disconnecting\/connecting, and make sure that it is free of foreign material.<\/div>\n<\/dd>\n<\/dl>\n<\/td>\n<\/tr>\n
\n
System wiring diagram<\/span><\/div>\n<\/td>\n
\n
\u2022 Not applicable<\/div>\n<\/td>\n<\/tr>\n
\n
Connector diagram<\/span><\/div>\n<\/td>\n
\n
\u2022 Not applicable<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n
\n
\n
Caution<\/div>\n<\/dd>\n
\n
\u2022 Verify the malfunction symptom according to not only the PID value but also the symptom troubleshooting.<\/div>\n<\/dd>\n<\/dl>\n

\n

Related PIDs<\/p>\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
\n

PIDs<\/p>\n<\/th>\n

\n

Reference<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
A\/C_REQ<\/div>\n<\/td>\n
\n
(See PID\/DATA MONITOR TABLE [PCM (SKYACTIV-G (US))]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
APP1<\/div>\n<\/td>\n<\/tr>\n
\n
APP2<\/div>\n<\/td>\n<\/tr>\n
\n
CLTCH_PEDAL_POS<\/div>\n<\/td>\n<\/tr>\n
\n
ECT<\/div>\n<\/td>\n<\/tr>\n
\n
ECT_VOLT<\/div>\n<\/td>\n<\/tr>\n
\n
ECT2<\/div>\n<\/td>\n<\/tr>\n
\n
ECT2_VOLT<\/div>\n<\/td>\n<\/tr>\n
\n
FUEL_PRES<\/div>\n<\/td>\n<\/tr>\n
\n
LOAD_CALC<\/div>\n<\/td>\n<\/tr>\n
\n
LONG_FUEL_TRIM<\/div>\n<\/td>\n<\/tr>\n
\n
A\/F_SEN_CUR<\/div>\n<\/td>\n<\/tr>\n
\n
HO2S_OUT_VOLT<\/div>\n<\/td>\n<\/tr>\n
\n
ENG_RPM<\/div>\n<\/td>\n<\/tr>\n
\n
SHRT_FUEL_TRIM<\/div>\n<\/td>\n<\/tr>\n
\n
TP_RELAT<\/div>\n<\/td>\n<\/tr>\n
\n
VSS<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

\n

Diagnostic Procedure<\/p>\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
\n

Step<\/p>\n<\/th>\n

\n

Inspection<\/p>\n<\/th>\n

\n

Results<\/p>\n<\/th>\n

\n

Action<\/p>\n<\/th>\n<\/tr>\n<\/thead>\n

\n
1<\/div>\n<\/td>\n
\n
INSPECT COOLING SYSTEM FOR MALFUNCTION<\/div>\n
\u2022 Access the ECT PID using the M-MDS. (See PID\/DATA MONITOR INSPECTION<\/a>.)<\/div>\n
\u2022 Start the engine and warm it up completely.<\/div>\n
\u2022 Is the ECT PID value between 82\u2014112 \u00b0C {180\u2014234 \u00b0F}<\/span>?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
ECT PID value is higher than 112 \u00b0C {234 \u00b0F}<\/span>:<\/div>\n
\u2022 Perform the symptom troubleshooting “COOLING SYSTEM CONCERNS-OVERHEATING”. (See COOLING SYSTEM CONCERNS-OVERHEATING [SKYACTIV-G (US)]<\/a>.)<\/div>\n
ECT PID value is less than 82 \u00b0C {180 \u00b0F}<\/span>:<\/div>\n
\u2022 Perform the symptom troubleshooting “COOLING SYSTEM CONCERNS-RUNS COLD”. (See COOLING SYSTEM CONCERNS-RUNS COLD [SKYACTIV-G]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
2<\/div>\n<\/td>\n
\n
VERIFY PCM DTC<\/div>\n
\u2022 Perform the DTC inspection for the PCM. (See DTC INSPECTION<\/a>.)<\/div>\n
\u2022 Are any DTCs displayed?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair the malfunctioning location according to the applicable DTC troubleshooting.<\/div>\n
(See DTC TABLE [PCM (SKYACTIV-G (US))]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
3<\/div>\n<\/td>\n
\n
VERIFY CURRENT INPUT SIGNAL STATUS<\/div>\n
\n
\n
Warning<\/div>\n<\/dd>\n
\n
\n
\u2022 While performing this step, always operate the vehicle in a safe and lawful manner.<\/div>\n
\u2022 When the M-MDS is used to observe monitor system status while driving, be sure to have another technician with you, or record the data in the M-MDS using the PID\/DATA MONITOR AND RECORD capturing function and inspect later.<\/div>\n<\/div>\n<\/dd>\n<\/dl>\n
\u2022 Access the following PIDs using the M-MDS: (See PID\/DATA MONITOR INSPECTION<\/a>.)<\/div>\n
\n
\n
\u2015 APP1<\/div>\n
\u2015 APP2<\/div>\n
\u2015 CLTCH_PEDAL_POS (MTX)<\/div>\n
\u2015 ECT<\/div>\n
\u2015 ECT_VOLT<\/div>\n
\u2015 ECT2<\/div>\n
\u2015 ECT2_VOLT<\/div>\n
\u2015 A\/F_SEN_CUR<\/div>\n
\u2015 HO2S_OUT_VOLT<\/div>\n
\u2015 SHRT_FUEL_TRIM<\/div>\n
\u2015 LONG_FUEL_TRIM<\/div>\n<\/dd>\n<\/dl>\n
\u2022 Do the PIDs indicate the correct values under the malfunction condition? (See PID\/DATA MONITOR TABLE [PCM (SKYACTIV-G (US))]<\/a>.)<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
APP1, APP2 PIDs are not as specified:<\/div>\n
\u2022 Inspect the APP sensor No.1 and No.2. (See ACCELERATOR PEDAL POSITION (APP) SENSOR INSPECTION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.) (See ACCELERATOR PEDAL POSITION (APP) SENSOR INSPECTION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
CLTCH_PEDAL_POS PID is not as specified: (MTX)<\/div>\n
\u2022 Inspect the clutch stroke sensor. (See CLUTCH STROKE SENSOR INSPECTION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.) (See CLUTCH STROKE SENSOR INSPECTION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
ECT, ECT_VOLT, ECT2, ECT2_VOLT PIDs are not as specified:<\/div>\n
\u2022 Inspect the ECT sensor No.1 and No.2. (See ENGINE COOLANT TEMPERATURE (ECT) SENSOR INSPECTION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.) (See ENGINE COOLANT TEMPERATURE (ECT) SENSOR INSPECTION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
A\/F_SEN_CUR, SHRT_FUEL_TRIM, LONG_FUEL_TRIM PIDs are not as specified:<\/div>\n
\u2022 Inspect the A\/F sensor. (See AIR FUEL RATIO (A\/F) SENSOR INSPECTION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.) (See AIR FUEL RATIO (A\/F) SENSOR INSPECTION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
HO2S_OUT_VOLT PID is not as specified:<\/div>\n
\u2022 Inspect the HO2S. (See HEATED OXYGEN SENSOR (HO2S) INSPECTION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.) (See HEATED OXYGEN SENSOR (HO2S) INSPECTION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
Repair or replace the malfunctioning location.<\/div>\n
\u2022 If the malfunction remains:<\/div>\n
\n
\n
\u2015 Inspect communication error between TCM and PCM. (ATX)<\/div>\n
\n
\n
\u2022 Repair or replace the malfunctioning location and perform the repair completion verification.<\/div>\n<\/dd>\n<\/dl>\n
\u2015 Perform the \u201cAction for Non-repeatable Malfunction\u201d procedure. (See TROUBLESHOOTING PROCEDURE [(US)]<\/a>.)<\/div>\n<\/dd>\n<\/dl>\n<\/td>\n<\/tr>\n
\n
4<\/div>\n<\/td>\n
\n
DETERMINE IF MALFUNCTION CAUSE IS A\/C REQUEST SIGNAL OR OTHER<\/div>\n
\u2022 Access the A\/C_REQ PID using the M-MDS. (See PID\/DATA MONITOR INSPECTION<\/a>.)<\/div>\n
\u2022 Monitor the A\/C_REQ PID while turning on and off the air conditioner using the switch on the control panel.<\/div>\n
\u2022 Does the A\/C_REQ PID value change from on to off according to switch control panel?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
If the A\/C_REQ PID is always ON:<\/div>\n
\u2022 Perform the symptom troubleshooting \u201cA\/C IS ALWAYS ON OR A\/C COMPRESSOR RUNS CONTINUOUSLY\u201d. (See A\/C IS ALWAYS ON OR A\/C COMPRESSOR RUNS CONTINUOUSLY [SKYACTIV-G]<\/a>.)<\/div>\n
If the A\/C_REQ PID is always OFF:<\/div>\n
\u2022 Perform the symptom troubleshooting \u201cA\/C DOES NOT WORK SUFFICIENTLY\u201d. (See A\/C DOES NOT WORK SUFFICIENTLY [SKYACTIV-G]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
5<\/div>\n<\/td>\n
\n
DETERMINE IF MALFUNCTION CAUSE IS DRIVE-BY-WIRE CONTROL SYSTEM OR OTHER<\/div>\n
\u2022 Will the engine run smoothly at part throttle?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to Step 7.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
6<\/div>\n<\/td>\n
\n
INSPECT DRIVE-BY-WIRE CONTROL SYSTEM OPERATION<\/div>\n
\u2022 Perform the Electronic Control Throttle Operation Inspection. (See ENGINE CONTROL SYSTEM OPERATION INSPECTION [SKYACTIV-G (US)]<\/a>.)<\/div>\n
\u2022 Does the drive-by-wire control system work properly?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Visually inspect the throttle body (damage\/scratching).<\/div>\n
\u2022 If there is any malfunction:<\/div>\n
\n
\n
\u2015 Repair or replace the malfunctioning location and perform the repair completion verification.<\/div>\n<\/dd>\n<\/dl>\n
\u2022 If there is no malfunction:<\/div>\n
\n
\n
\u2015 Go to the next step.<\/div>\n<\/dd>\n<\/dl>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Repair or replace the malfunctioning location and perform the repair completion verification.<\/div>\n<\/td>\n<\/tr>\n
\n
7<\/div>\n<\/td>\n
\n
INSPECT FUEL INJECTOR OPERATION<\/div>\n
\u2022 Perform the Fuel Injector Operation Inspection. (See FUEL INJECTOR INSPECTION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.) (See FUEL INJECTOR INSPECTION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
\u2022 Do the fuel injectors operate properly?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Repair or replace the malfunctioning location and perform the repair completion verification.<\/div>\n<\/td>\n<\/tr>\n
\n
8<\/div>\n<\/td>\n
\n
INSPECT HIGH PRESSURE FUEL PUMP<\/div>\n
\u2022 Inspect the high pressure fuel pump. (See HIGH PRESSURE FUEL PUMP INSPECTION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.) (See HIGH PRESSURE FUEL PUMP INSPECTION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
\u2022 Is there any malfunction?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Replace the high pressure fuel pump and perform the repair completion verification.<\/div>\n
(See HIGH PRESSURE FUEL PUMP REMOVAL\/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
(See HIGH PRESSURE FUEL PUMP REMOVAL\/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Go to the next step.<\/div>\n<\/td>\n<\/tr>\n
\n
9<\/div>\n<\/td>\n
\n
INSPECT INTAKE-AIR SYSTEM FOR AIR LEAKAGE<\/div>\n
\u2022 Inspect for leakage in intake-air system.<\/div>\n
\u2022 Is there any leakage?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Repair or replace the malfunctioning location and perform the repair completion verification.<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Injector driver malfunction.<\/div>\n
\u2022 Replace the PCM. (See PCM REMOVAL\/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.) (See PCM REMOVAL\/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
If the problem remains, overhaul the engine and perform the repair completion verification.<\/div>\n<\/td>\n<\/tr>\n
\n
Repair completion verification 1<\/div>\n<\/td>\n
\n
VERIFY THAT VEHICLE IS REPAIRED<\/div>\n
\u2022 Install\/connect the part removed\/disconnected during the troubleshooting procedure.<\/div>\n
\u2022 Has the malfunction symptom been eliminated?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Complete the symptom troubleshooting. (Explain contents of repair to customer)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.<\/div>\n
(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(US)]<\/a>.)<\/div>\n
\u2022 If the CAN communication is normal, perform the diagnosis from Step 1.<\/div>\n
\n
\n
\u2015 If the malfunction recurs, go to the next step.<\/div>\n<\/dd>\n<\/dl>\n<\/td>\n<\/tr>\n
\n
Repair completion verification 2<\/div>\n<\/td>\n
\n
VERIFY IF MALFUNCTION IS CAUSED BY NOT PERFORMING PCM REPROGRAMMING<\/div>\n
\u2022 Verify repair information and verify that there is a new calibration in the PCM.<\/div>\n
\u2022 Is there a new calibration in the PCM?<\/div>\n<\/td>\n
\n
Yes<\/div>\n<\/td>\n
\n
Perform the PCM reprogramming and verify if the malfunction symptom was corrected.<\/div>\n
\u2022 If the malfunction recurs, replace the PCM. (See PCM REMOVAL\/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.) (See PCM REMOVAL\/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n
\n
No<\/div>\n<\/td>\n
\n
Replace the PCM.<\/div>\n
(See PCM REMOVAL\/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n
(See PCM REMOVAL\/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))]<\/a>.)<\/div>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n
<\/div>\n
<\/div>\n
<\/div>\n

<\/div>\n<\/div>\n","protected":false},"excerpt":{"rendered":"

FAST IDLE\/RUNS ON [SKYACTIV-G (US)] SM2565584 id0103s48896s6 Troubleshooting item Fast idle\/runs on Description \u2022 Engine speed continues at fast idle after warm-up. \u2022 Engine runs after ignition is switched off. Possible cause \u2022 Cooling system malfunction \u2022 PCM DTC is stored \u2022 Accelerator pedal stuck depressed \u2022 Erratic signal to PCM \u2015 APP sensor or related circuit malfunction \u2015 Clutch stroke sensor or related circuit malfunction (MTX) \u2015 Communication error between TCM and PCM (ATX) […]<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_monsterinsights_skip_tracking":false,"_monsterinsights_sitenote_active":false,"_monsterinsights_sitenote_note":"","_monsterinsights_sitenote_category":0,"footnotes":""},"class_list":["post-10029","page","type-page","status-publish","hentry"],"_links":{"self":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages\/10029","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/comments?post=10029"}],"version-history":[{"count":0,"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/pages\/10029\/revisions"}],"wp:attachment":[{"href":"https:\/\/www.hexorcism.com\/19BP\/wp-json\/wp\/v2\/media?parent=10029"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}