DETERMINING SHORT TO GROUND LOCATION (CAN-BUS No.6) [(US)]
DETERMINING SHORT TO GROUND LOCATION (CAN-BUS No.6) [(US)]
SM2566464
id1002x1003800
-
Caution
-
• Perform the following malfunction diagnosis only when it is diagnosed with a short to ground by CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(US)].)
System Wiring Diagram
am3zzw00027509
|
Determination Procedure
-
Caution
-
• When disconnecting the connector, verify that there is no looseness, damage, deformation, corrosion, or poor connection of the connector terminals.• When inspecting the connector, touch it with a paper clip or similar thin pin without directly inserting a tester probe into the terminal.
|
Step |
Inspection |
Action |
|
|---|---|---|---|
|
1
|
INSPECT FOR SHORT TO GROUND BETWEEN BODY CONTROL MODULE (BCM) AND CONNECTOR C-08
• Switch the ignition off.
• Disconnect the negative battery cable. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)])
• Disconnect the connector C-10.
• Inspect for continuity at the following terminals:
• Is there continuity?
|
Yes
|
Go to the next step.
|
|
No
|
Go to Step 3.
|
||
|
2
|
INSPECT CAN LINE IN BODY CONTROL MODULE (BCM) FOR SHORT TO GROUND
• Disconnect the connector 2 which has body control module (BCM) terminals 2A and 2C.
• Inspect for continuity at the following terminals:
• Is there continuity?
|
Yes
|
Repair or replace the wiring harness between the connector C-10 and body control module (BCM) because the wiring harness is shorted to ground.
|
|
No
|
Replace the body control module (BCM) because there is a short to ground in the body control module (BCM).
|
||
|
3
|
INSPECT FOR SHORT TO GROUND BETWEEN REAR SIDE RADAR SENSOR (LH) AND CONNECTOR C-10
• Inspect for continuity at the following terminals:
• Is there continuity?
|
Yes
|
Go to the next step.
|
|
No
|
Go to Step 5.
|
||
|
4
|
INSPECT CAN LINE IN REAR SIDE RADAR SENSOR (LH) FOR SHORT TO GROUND
• Disconnect the rear side radar sensor (LH) connector.
• Inspect for continuity at the following terminals:
• Is there continuity?
|
Yes
|
Repair or replace the wiring harness between the rear side radar sensor (LH) and connector C-10 because the wiring harness is shorted to ground.
|
|
No
|
Replace the rear side radar sensor (LH) because there is a short to ground in the rear side radar sensor (LH).
|
||
|
5
|
INSPECT FOR SHORT TO GROUND BETWEEN FRONT RADAR SENSOR AND CONNECTOR C-10
• Inspect for continuity at the following terminals:
• Is there continuity?
|
Yes
|
Go to the next step.
|
|
No
|
Go to Step 7.
|
||
|
6
|
INSPECT CAN LINE IN FRONT RADAR SENSOR FOR SHORT TO GROUND
• Disconnect the front radar sensor connector.
• Inspect for continuity at the following terminals:
• Is there continuity?
|
Yes
|
Repair or replace the wiring harness between the front radar sensor and connector C-10 because the wiring harness is shorted to ground.
|
|
No
|
Replace the front radar sensor because there is a short to ground in the front radar sensor.
|
||
|
7
|
INSPECT FOR SHORT TO GROUND BETWEEN CONNECTOR C-10 AND CONNECTOR C-06
• Disconnect the connector C-06.
• Connect the connector C-10.
• Inspect for continuity at the following terminals:
• Is there continuity?
|
Yes
|
Repair or replace the wiring harness between the connector C-10 and connector C-06 because the wiring harness is shorted to ground.
|
|
No
|
Go to the next step.
|
||
|
8
|
INSPECT CAN LINE IN BODY CONTROL MODULE (BCM) FOR SHORT TO GROUND
• Disconnect the body control module (BCM).
• Inspect for continuity at the following terminals:
• Is there continuity?
|
Yes
|
Repair or replace the wiring harness between the body control module (BCM) and connector C-06 because the wiring harness is shorted to ground.
|
|
No
|
Replace the body control module (BCM) because there is a short to ground in the body control module (BCM).
|
||