DTC P2610:00 [PCM (SKYACTIV-G)]
DTC P2610:00 [PCM (SKYACTIV-G)]
SM2334456
id0102t4303800
Outline
System malfunction location |
Malfunction in body control module (BCM) |
||||
---|---|---|---|---|---|
Detection condition
|
• Malfunction detected in body control module (BCM).
Precondition
• Switch the ignition ON (engine on)
• The following DTCs are not detected:
|
||||
Fail-safe
|
• The fast idle up correction for the drive-by-wire control is inhibited.
|
||||
Possible cause
|
• Body control module (BCM) malfunction
• PCM malfunction
|
||||
System wiring diagram
|
• Not applicable
|
||||
Connector diagram
|
• Not applicable
|
Diagnostic Procedure
Step |
Inspection |
Results |
Action |
---|---|---|---|
1
|
RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION
• Record the freeze frame data/snapshot data.
|
—
|
Go to the next step.
|
2
|
VERIFY RELATED REPAIR INFORMATION OR SERVICE INFORMATION AVAILABILITY
• Verify related Service Bulletins, on-line repair information, or Service Information availability.
• Is any related Information available?
|
Yes
|
Perform repair or diagnosis according to the available information.
• If the vehicle is not repaired, go to the next step.
|
No
|
Go to the next step.
|
||
3
|
VERIFY BODY CONTROL MODULE (BCM) DTC
• Perform the DTC inspection for the body control module (BCM). (See DTC INSPECTION.)
• Are any DTCs displayed?
|
Yes
|
Repair the malfunctioning location according to the applicable DTC troubleshooting.
|
No
|
Go to the next step.
|
||
4
|
INSPECT BODY CONTROL MODULE (BCM) BACKUP VOLTAGE CIRCUIT
• Switch the ignition off.
• Remove the MAIN 200 A fuse, F27 25 A fuse and F50 15 A fuse.
• Inspect the MAIN 200 A fuse, F27 25 A fuse and F50 15 A fuse.
• Is there any malfunction?
|
Yes
|
Replace the malfunctioning fuse.
Switch the ignition ON (engine on) and wait for 10 s or more.
Switch the ignition off.
Go to repair completion verification.
|
No
|
Replace the body control module (BCM) and perform the repair completion verification.
|
||
Repair completion verification 1
|
VERIFY THAT VEHICLE IS REPAIRED
• Install/connect the part removed/disconnected during the troubleshooting procedure.
• Start the engine.
• Stop the engine.
• Clear the DTC recorded in the memory. (See CLEARING DTC.)
• Replicate the vehicle conditions at the time the DTC was detected using the following procedure.
• Perform the DTC inspection for the PCM. (See DTC INSPECTION.)
• Is the same Pending DTC present?
|
Yes
|
Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.
If the CAN communication is normal, perform the diagnosis from Step 1.
• If the malfunction recurs, replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))].) (See PCM REMOVAL/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))].)
|
No
|
Go to the next step.
|
||
Repair completion verification 2
|
VERIFY IF OTHER DTCs DISPLAYED
• Perform the DTC inspection. (See DTC INSPECTION.)
• Are any other DTCs displayed?
|
Yes
|
Repair the malfunctioning location according to the applicable DTC troubleshooting.
|
No
|
DTC troubleshooting completed.
|