Menu +
Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

DTC P0807:00 [PCM (SKYACTIV-G (US))]

DTC P0807:00 [PCM (SKYACTIV-G (US))]

SM2565552


id0102t46167u0



Outline

System malfunction location

Clutch stroke sensor circuit low input

Detection condition
• The output voltage of the clutch stroke sensor is less than 0.22 V for a continuous 0.5 s.
Precondition
• Battery voltage: 8—16 V
0.5 s have elapsed after the ignition was switched ON (engine off or on)
Fail-safe
• Not applicable
Possible cause
• Clutch stroke sensor incorrect installation
• Clutch stroke sensor connector or terminals malfunction
• PCM connector or terminals malfunction
• Short to ground in any of the following clutch stroke sensor circuits.
― Power supply circuit
― Signal circuit
• Short circuit in clutch stroke sensor signal circuit and ground circuit
• Open circuit in any of the following clutch stroke sensor circuits.
― Power supply circuit
― Signal circuit
• Clutch stroke sensor malfunction
• PCM malfunction



Diagnostic Procedure

Step

Inspection

Results

Action

1
RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION
• Record the freeze frame data/snapshot data.

Note
• Recording can be facilitated using the screen capture function of the PC.
Go to the next step.
2
VERIFY RELATED REPAIR INFORMATION OR SERVICE INFORMATION AVAILABILITY
• Verify related Service Bulletins, on-line repair information, or Service Information availability.
• Is any related Information available?
Yes
Perform repair or diagnosis according to the available information.
• If the vehicle is not repaired, go to the next step.
No
Go to the next step.
3
VERIFY IF CLUTCH STROKE SENSOR IS INSTALLED CORRECTLY
• Verify the clutch stroke sensor installation condition. (See CLUTCH MASTER CYLINDER REMOVAL/INSTALLATION [C66M-R (US)].)
• Is the installation condition normal?
Yes
Go to the next step.
No
Correctly install the clutch stroke sensor and perform the repair completion verification.
4
INSPECT CLUTCH STROKE SENSOR CONNECTOR FOR MALFUNCTION
• Inspect the applicable connector and terminal. (See CONNECTOR INSPECTION.)
• Are the connector and terminal normal?
Yes
Go to the next step.
No
Repair or replace the malfunctioning location and perform the repair completion verification.
5
INSPECT PCM CONNECTOR FOR MALFUNCTION
• Inspect the applicable connector and terminal. (See CONNECTOR INSPECTION.)
• Are the connector and terminal normal?
Yes
Go to the next step.
No
Repair or replace the malfunctioning location and perform the repair completion verification.
6
INSPECT CLUTCH STROKE SENSOR POWER SUPPLY CIRCUIT AND SIGNAL CIRCUIT FOR SHORT TO GROUND
• Inspect the applicable circuit for a short to ground. (See CIRCUIT INSPECTION.)
• Is the circuit normal?
Yes
Go to the next step.
No
Repair or replace the malfunctioning location and perform the repair completion verification.
7
INSPECT CLUTCH STROKE SENSOR SIGNAL CIRCUIT AND GROUND CIRCUIT FOR SHORT CIRCUIT
• Inspect the applicable circuits for a short circuit. (See CIRCUIT INSPECTION.)
• Is the circuit normal?
Yes
Go to the next step.
No
Repair or replace the malfunctioning location and perform the repair completion verification.
8
INSPECT CLUTCH STROKE SENSOR POWER SUPPLY CIRCUIT AND SIGNAL CIRCUIT FOR OPEN CIRCUIT
• Inspect the applicable circuit for open circuit. (See CIRCUIT INSPECTION.)
• Is the circuit normal?
Yes
Go to the next step.
No
Repair or replace the malfunctioning location and perform the repair completion verification.
9
INSPECT CLUTCH STROKE SENSOR FOR MALFUNCTION
• Is the part normal?
Yes
Go to the next step.
No
Repair or replace the malfunctioning location and perform the repair completion verification.
Repair completion verification 1
VERIFY THAT VEHICLE IS REPAIRED
• Install/connect the part removed/disconnected during the troubleshooting procedure.
• Clear the DTC recorded in the memory. (See CLEARING DTC.)
• Replicate the vehicle conditions at the time the DTC was detected using the following procedure.
― Switch the ignition ON (engine off or on) and wait for 10 s or more.
• Perform the DTC inspection for the PCM. (See DTC INSPECTION.)
• Is the same Pending DTC present?
Yes
Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.
If the CAN communication is normal, perform the diagnosis from Step 1.
No
Go to the next step.
Repair completion verification 2
VERIFY IF OTHER DTCs DISPLAYED
• Perform the DTC inspection. (See DTC INSPECTION.)
• Are any other DTCs displayed?
Yes
Repair the malfunctioning location according to the applicable DTC troubleshooting.
No
DTC troubleshooting completed.