Menu +
Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

DTC P2504:00 [PCM (SKYACTIV-G)]

DTC P2504:00 [PCM (SKYACTIV-G)]

SM2334554


id0102t4709700

Note
• To determine the malfunctioning part, proceed with the diagnostics from “Function Inspection Using M-MDS”.



Details On DTCs

Description

Generator system: Voltage generated by generator is high

Detection condition
Determination conditions
• The voltage generated by the generator is 18.5 V or higher or the battery voltage is 16 V or higher for a continuous specified time.
Preconditions
• While engine is running
Malfunction determination period
5 s period
Drive cycle
• 1
Self test type
• CMDTC self test
Sensor used
• PCM
• Generator
Fail-safe function
• Generator control is inhibited.
Vehicle status when DTCs are output
• The following vehicle conditions differ depending on the type of malfunction:
― Vehicle shock may occur due to generator load.
― Idling feel due to generator-stop may occur.
Possible cause
• Poor connection of the following parts:
― Battery
― Generator
― PCM
• Connector or terminal malfunction of the following parts:
― Battery
― Generator
― PCM
• Short to power supply in generator charge/discharge circuit
• Short to ground or open circuit in generator charge/discharge circuit
• Generator malfunction
• Battery malfunction
• PCM malfunction



Function Explanation (DTC Detection Outline)

• When the charge/discharge circuit for the power supplying the vehicle is normal, the vehicle will operate normally.
• The PCM determines an over-charge malfunction by detecting that the generator terminal voltage or battery terminal voltage are abnormally high, and verification of vehicle malfunctions/safety assurance is performed.



Repeatability Verification Procedure

1. Clear the DTC from the PCM memory using the M-MDS. (See CLEARING DTC.)
2. Start the engine.
3. Leave for 30 s while idling with no electrical load.
4. Leave for 30 s while idling with high electrical load.



PID Item/Simulation Item Used In Diagnosis

• Not applicable



Function Inspection Using M-MDS

Step

Inspection

Results

Action

1
PURPOSE: RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION
• Record the freeze frame data/snapshot data.

Note
• Recording can be facilitated using the screen capture function of the PC.
Go to Troubleshooting Diagnostic Procedure to perform the procedure from Step 1.



Troubleshooting Diagnostic Procedure

Intention of troubleshooting procedure
• Step 1—7
― Perform an inspection of each signal transmission system.
• Step 8
― Perform a unit inspection of the generator.
• Step 9
― Perform a unit inspection of the battery.
• Repair completion verification
― Verify that the primary malfunction is resolved and there are no other malfunctions.

Step

Inspection

Results

Action

1
PURPOSE: VERIFY RELATED REPAIR INFORMATION OR SERVICE INFORMATION AVAILABILITY
• Verify related Service Bulletins, on-line repair information, or Service Information availability.
• Is any related Information available?
Yes
Perform repair or diagnosis according to the available information.
• If the vehicle is not repaired, go to the next step.
No
Go to the next step.
2
PURPOSE: VERIFY IF POOR CONNECTION OF EACH PART AFFECTS DIAGNOSTIC RESULTS
• Switch the ignition off.
• Inspect the connection condition (part installation condition, connector connection condition) for the following parts:
― Battery
― Generator
― PCM
• Is the connection condition (part installation condition, connector connection condition) for each part normal?
Yes
Go to the next step.
No
Connect each part or the connector correctly, then go to Step 9.
3
PURPOSE: INSPECT BATTERY CONNECTOR FOR MALFUNCTION
• Inspect the applicable connector and terminal. (See CONNECTOR INSPECTION.)
• Are the connector and terminal normal?
Yes
Go to the next step.
No
Repair or replace the malfunctioning location, then go to Step 9.
4
PURPOSE: INSPECT GENERATOR CONNECTOR FOR MALFUNCTION
• Inspect the applicable connector and terminal. (See CONNECTOR INSPECTION.)
• Are the connector and terminal normal?
Yes
Go to the next step.
No
Repair or replace the malfunctioning location, then go to Step 9.
5
PURPOSE: INSPECT PCM CONNECTOR FOR MALFUNCTION
• Inspect the applicable connector and terminal. (See CONNECTOR INSPECTION.)
• Are the connector and terminal normal?
Yes
Go to the next step.
No
Repair or replace the malfunctioning location, then go to Step 9.
6
PURPOSE: INSPECT GENERATOR CHARGE/DISCHARGE CIRCUIT FOR SHORT TO POWER SUPPLY
• Inspect the applicable circuit for a short to power supply. (See CIRCUIT INSPECTION.)
• Is the circuit normal?
Yes
Go to the next step.
No
Repair or replace the malfunctioning location, then go to Step 9.
7
PURPOSE: INSPECT GENERATOR CHARGE/DISCHARGE CIRCUIT FOR SHORT TO GROUND AND OPEN CIRCUIT
• Inspect the power supply circuit for an open circuit and short to ground. (See CIRCUIT INSPECTION.)
• Is the circuit normal?
Yes
Go to the next step.
No
Repair or replace the malfunctioning location, then go to Step 9.
8
PURPOSE: INSPECT GENERATOR FOR MALFUNCTION
• Is the part normal?
Yes
Go to the next step.
No
Repair or replace the malfunctioning location, then go to the next step.
9
PURPOSE: VERIFY CONDITIONS OF BATTERY
• Inspect the battery. (See BATTERY INSPECTION [(US)].)
Follow the inspection instructions.
Go to repair completion verification.
Repair completion verification 1
PURPOSE: VERIFY THAT VEHICLE IS REPAIRED
• Install/connect the part removed/disconnected during the troubleshooting procedure.
• Clear the DTC recorded in the memory. (See CLEARING DTC.)
• Replicate the vehicle conditions at the time the DTC was detected using the following procedure.
― Implement the repeatability verification procedure. (See Repeatability Verification Procedure.)
• Perform the DTC inspection for the PCM. (See DTC INSPECTION.)
• Is the same Pending DTC present?
Yes
Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.
If the CAN communication is normal, perform the diagnosis from Step 1.
No
Go to the next step.
Repair completion verification 2
PURPOSE: VERIFY IF OTHER DTCs DISPLAYED
• Perform the DTC inspection. (See DTC INSPECTION.)
• Are any other DTCs displayed?
Yes
Repair the malfunctioning location according to the applicable DTC troubleshooting.
No
DTC troubleshooting completed.