Menu +
Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

DETERMINING SHORT TO POWER SUPPLY LOCATION (CAN-BUS No.3) [(US)]

DETERMINING SHORT TO POWER SUPPLY LOCATION (CAN-BUS No.3) [(US)]

SM2566453


id1002x1002700

Caution
• Perform the following malfunction diagnosis only when it is diagnosed with a short to ground by CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(US)].)



System Wiring Diagram

am3zzw00027514



Determination Procedure

Caution
• When disconnecting the connector, verify that there is no looseness, damage, deformation, corrosion, or poor connection of the connector terminals.
• When inspecting the connector, touch it with a paper clip or similar thin pin without directly inserting a tester probe into the terminal.
• Disconnect the negative battery terminal before performing any work that requires handling of connectors.

Step

Inspection

Action

1
INSPECT CAN LINE BETWEEN BODY CONTROL MODULE (BCM) AND CONNECTOR C-32 FOR SHORT TO POWER SUPPLY
• Switch the ignition off.
• Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the connector C-32.
• Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2L and 2J.
• Is the voltage between 1.5—3.5 V?
Yes
Go to Step 3.
No
Go to the next step.
2
INSPECT BODY CONTROL MODULE (BCM) FOR SHORT TO POWER SUPPLY
• Switch the ignition off.
• Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the connector 2 which has body control module (BCM) terminals 2L and 2J.
• Connect the connector C-32.
• Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2L and 2J (wiring harness side).
• Is the voltage between 1.5—3.5 V?
Yes
Replace the body control module (BCM) because there is a short to the power supply in the body control module (BCM).
No
Repair or replace the wiring harness between the body control module (BCM) and connector C-32 because the wiring harness is shorted to the power supply.
3
INSPECT CAN LINE BETWEEN FRONT COMBINATION LIGHT (LH) AND CONNECTOR C-32 FOR SHORT TO POWER SUPPLY
• Measure the voltage at front combination light (LH) terminals E and D.
• Is the voltage between 1.5—3.5 V?
Yes
Go to Step 5.
No
Go to the next step.
4
INSPECT FRONT COMBINATION LIGHT (LH) FOR SHORT TO POWER SUPPLY
• Switch the ignition off.
• Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the front combination light (LH) connector.
• Connect the connector C-32.
• Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2L and 2J.
• Is the voltage between 1.5—3.5 V?
Yes
Replace the front combination light (LH) because there is a short to the power supply in the front combination light (LH).
No
Repair or replace the wiring harness between the front combination light (LH) and connector C-32 because the wiring harness is shorted to the power supply.
5
INSPECT CAN LINE BETWEEN CONNECTOR C-33 AND CONNECTOR C-32 FOR SHORT TO POWER SUPPLY
• Switch the ignition off.
• Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the connector C-33.
• Connect the connector C-32.
• Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2L and 2J.
• Is the voltage between 1.5—3.5 V?
Yes
Go to the next step.
No
Repair or replace the wiring harness between connector C-33 and connector C-32 because the wiring harness is shorted to the power supply.
6
INSPECT CAN LINE BETWEEN FRONT COMBINATION LIGHT (RH) AND CONNECTOR C-33 FOR SHORT TO POWER SUPPLY
• Measure the voltage at front combination light (RH) terminals E and D.
• Is the voltage between 1.5—3.5 V?
Yes
Go to Step 8.
No
Go to the next step.
7
INSPECT FRONT COMBINATION LIGHT (RH) FOR SHORT TO POWER SUPPLY
• Switch the ignition off.
• Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the front combination light (RH) connector.
• Connect the connector C-33.
• Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2L and 2J.
• Is the voltage between 1.5—3.5 V?
Yes
Replace the front combination light (RH) because there is a short to the power supply in the front combination light (RH).
No
Repair or replace the wiring harness between the front combination light (RH) and connector C-33 because the wiring harness is shorted to the power supply.
8
INSPECT CAN LINE BETWEEN CONNECTOR C-04 AND CONNECTOR C-33 FOR SHORT TO POWER SUPPLY
• Switch the ignition off.
• Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the connector C-04.
• Connect the connector C-33.
• Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2L and 2J.
• Is the voltage between 1.5—3.5 V?
Yes
Go to the next step.
No
Repair or replace the wiring harness between connector C-04 and connector C-33 because the wiring harness is shorted to the power supply.
9
INSPECT CAN LINE BETWEEN CLIMATE CONTROL UNIT AND CONNECTOR C-04 FOR SHORT TO POWER SUPPLY
• Switch the ignition off.
• Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the climate control unit connector.
• Connect the connector C-04.
• Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2L and 2J.
• Is the voltage between 1.5—3.5 V?
Yes
Go to the next step.
No
Repair or replace the wiring harness between the climate control unit and connector C-04 because the wiring harness is shorted to the power supply.
10
INSPECT CAN LINE BETWEEN CLIMATE CONTROL UNIT AND ACTIVE DRIVING DISPLAY FOR SHORT TO POWER SUPPLY
• Measure the voltage at active driving display terminals I and G.
• Is the voltage between 1.5—3.5 V?
Yes
Go to Step 12.
No
Go to the next step.
11
INSPECT ACTIVE DRIVING DISPLAY FOR SHORT TO POWER SUPPLY
• Switch the ignition off.
• Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the active driving display connector.
• Connect the climate control unit connector.
• Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2L and 2J.
• Is the voltage between 1.5—3.5 V?
Yes
Replace the active driving display because there is a short to the power supply in the active driving display.
No
Repair or replace the wiring harness between the active driving display and climate control unit because the wiring harness is shorted to the power supply.
12
INSPECT CAN LINE BETWEEN CLIMATE CONTROL UNIT AND ESU FOR SHORT TO POWER SUPPLY
• Measure the voltage at ESU terminals 3A and 3C.
• Is the voltage between 1.5—3.5 V?
Yes
Replace the climate control unit because there is a short to the power supply in the climate control unit.
No
Go to the next step.
13
INSPECT CAN LINE BETWEEN CONNECTOR C-40 AND CLIMATE CONTROL UNIT FOR SHORT TO POWER SUPPLY
• Switch the ignition off.
• Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the connector C-40.
• Connect the climate control unit connector.
• Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2L and 2J.
• Is the voltage between 1.5—3.5 V?
Yes
Go to the next step.
No
Repair or replace the wiring harness between connector C-40 and climate control unit because the wiring harness is shorted to the power supply.
14
INSPECT CAN LINE BETWEEN STEERING ANGLE SENSOR AND CONNECTOR C-40 FOR SHORT TO POWER SUPPLY
• Measure the voltage at steering angle sensor terminals B and D.
• Is the voltage between 1.5—3.5 V?
Yes
Go to Step 16.
No
Go to the next step.
15
INSPECT STEERING ANGLE SENSOR FOR SHORT TO POWER SUPPLY
• Switch the ignition off.
• Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the steering angle sensor connector.
• Connect the connector C-40.
• Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2L and 2J.
• Is the voltage between 1.5—3.5 V?
Yes
Replace the steering angle sensor because there is a short to the power supply in the steering angle sensor.
No
Repair or replace the wiring harness between the steering angle sensor and connector C-40 because the wiring harness is shorted to the power supply.
16
INSPECT CAN LINE BETWEEN INSTRUMENT CLUSTER AND CONNECTOR C-40 FOR SHORT TO POWER SUPPLY
• Measure the voltage at instrument cluster terminals AK and AM.
• Is the voltage between 1.5—3.5 V?
Yes
Go to Step 18.
No
Go to the next step.
17
INSPECT INSTRUMENT CLUSTER FOR SHORT TO POWER SUPPLY
• Switch the ignition off.
• Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the instrument cluster connector.
• Connect the connector C-40.
• Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2L and 2J.
• Is the voltage between 1.5—3.5 V?
Yes
Replace the instrument cluster because there is a short to the power supply in the instrument cluster.
No
Repair or replace the wiring harness between the instrument cluster and connector C-40 because the wiring harness is shorted to the power supply.
18
INSPECT CAN LINE BETWEEN CONNECTOR C-13 AND CONNECTOR C-40 FOR SHORT TO POWER SUPPLY
• Switch the ignition off.
• Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the connector C-13.
• Connect the connector C-40.
• Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2L and 2J.
• Is the voltage between 1.5—3.5 V?
Yes
Go to the next step.
No
Repair or replace the wiring harness between connector C-13 and connector C-40 because the wiring harness is shorted to the power supply.
19
INSPECT CAN LINE BETWEEN CONNECTOR C-48 AND CONNECTOR C-13 FOR SHORT TO POWER SUPPLY
• Switch the ignition off.
• Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the connector C-48.
• Connect the connector C-13.
• Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2L and 2J.
• Is the voltage between 1.5—3.5 V?
Yes
Go to the next step.
No
Repair or replace the wiring harness between connector C-48 and connector C-13 because the wiring harness is shorted to the power supply.
20
INSPECT CAN LINE BETWEEN DOOR-ELECTRICAL SUPPLY UNIT (PASSENGER’S SIDE) AND CONNECTOR C-48 FOR SHORT TO POWER SUPPLY
• Measure the voltage at door-electrical supply unit (passenger’s side) terminals 1A and 1B.
• Is the voltage between 1.5—3.5 V?
Yes
Go to Step 23.
No
Go to the next step.
21
INSPECT CAN LINE BETWEEN DOOR-ELECTRICAL SUPPLY UNIT (PASSENGER’S SIDE) AND CONNECTOR C-23 FOR SHORT TO POWER SUPPLY
• Switch the ignition off.
• Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the connector C-23.
• Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at door-electrical supply unit (passenger’s side) terminals 1A and 1B.
• Is the voltage between 1.5—3.5 V?
Yes
Repair or replace the wiring harness between connector C-48 and connector C-23 because the wiring harness is shorted to the power supply.
No
Go to the next step.
22
INSPECT DOOR-ELECTRICAL SUPPLY UNIT (PASSENGER’S SIDE) FOR SHORT TO POWER SUPPLY
• Switch the ignition off.
• Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the door-electrical supply unit (passenger’s side) connector.
• Connect the connector C-23.
• Connect the connector C-48.
• Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2L and 2J.
• Is the voltage between 1.5—3.5 V?
Yes
Replace the door-electrical supply unit (passenger’s side) because there is a short to the power supply in the door-electrical supply unit (passenger’s side).
No
Repair or replace the wiring harness between the door-electrical supply unit (passenger’s side) and connector C-23 because the wiring harness is shorted to the power supply.
23
INSPECT JB No.2 FOR SHORT TO POWER SUPPLY
• Switch the ignition off.
• Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the connector C-49.
• Connect the connector C-48.
• Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2L and 2J.
• Is the voltage between 1.5—3.5 V?
Yes
Go to the next step.
No
Replace the JB No.2 because there is a short to the power supply in the JB No.2.
24
INSPECT CAN LINE BETWEEN LF CONTROL UNIT AND CONNECTOR C-49 FOR SHORT TO POWER SUPPLY
• Measure the voltage at LF control unit terminals M and P.
• Is the voltage between 1.5—3.5 V?
Yes
Go to Step 26.
No
Go to the next step.
25
INSPECT LF CONTROL UNIT FOR SHORT TO POWER SUPPLY
• Switch the ignition off.
• Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the LF control unit connector.
• Connect the connector C-49.
• Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2L and 2J.
• Is the voltage between 1.5—3.5 V?
Yes
Replace the LF control unit because there is a short to the power supply in the LF control unit.
No
Repair or replace the wiring harness between the LF control unit and connector C-49 because the wiring harness is shorted to the power supply.
26
INSPECT CAN LINE BETWEEN DASH-ELECTRICAL SUPPLY UNIT AND CONNECTOR C-49 FOR SHORT TO POWER SUPPLY
• Switch the ignition off.
• Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the dash-electrical supply unit connector.
• Connect the connector C-49.
• Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2L and 2J.
• Is the voltage between 1.5—3.5 V?
Yes
Go to the next step.
No
Repair or replace the wiring harness between the dash-electrical supply unit and connector C-49 because the wiring harness is shorted to the power supply.
27
INSPECT CAN LINE BETWEEN SHIFT PANEL (INDICATOR) AND DASH-ELECTRICAL SUPPLY UNIT FOR SHORT TO POWER SUPPLY
• Measure the voltage at shift panel (indicator) terminals E and F.
• Is the voltage between 1.5—3.5 V?
Yes
Go to Step 29.
No
Go to the next step.
28
INSPECT SHIFT PANEL (INDICATOR) FOR SHORT TO POWER SUPPLY
• Switch the ignition off.
• Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the shift panel (indicator) connector.
• Connect the dash-electrical supply unit connector.
• Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2L and 2J.
• Is the voltage between 1.5—3.5 V?
Yes
Replace the shift panel (indicator) because there is a short to the power supply in the shift panel (indicator).
No
Repair or replace the wiring harness between the shift panel (indicator) and dash-electrical supply unit because the wiring harness is shorted to the power supply.
29
INSPECT CAN LINE BETWEEN ESU AND DASH-ELECTRICAL SUPPLY UNIT FOR SHORT TO POWER SUPPLY
• Measure the voltage at ESU terminals 3A and 3C.
• Is the voltage between 1.5—3.5 V?
Yes
Replace the dash-electrical supply unit because there is a short to the power supply in the dash-electrical supply unit.
No
Go to the next step.
30
INSPECT CAN LINE BETWEEN CONNECTOR C-46 AND DASH-ELECTRICAL SUPPLY UNIT FOR SHORT TO POWER SUPPLY
• Switch the ignition off.
• Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the connector C-46.
• Connect the dash-electrical supply unit connector.
• Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2L and 2J.
• Is the voltage between 1.5—3.5 V?
Yes
Go to the next step.
No
Repair or replace the wiring harness between the dash-electrical supply unit and connector C-46 because the wiring harness is shorted to the power supply.
31
INSPECT JB No.1 FOR SHORT TO POWER SUPPLY
• Switch the ignition off.
• Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the connector C-47.
• Connect the connector C-46.
• Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2L and 2J.
• Is the voltage between 1.5—3.5 V?
Yes
Go to the next step.
No
Replace the JB No.1 because there is a short to the power supply in the JB No.1.
32
INSPECT CAN LINE BETWEEN DOOR-ELECTRICAL SUPPLY UNIT (DRIVER’S SIDE) AND CONNECTOR C-47 FOR SHORT TO POWER SUPPLY
• Measure the voltage at door-electrical supply unit (driver’s side) terminals 1A and 1B.
• Is the voltage between 1.5—3.5 V?
Yes
Go to Step 35.
No
Go to the next step.
33
INSPECT CAN LINE BETWEEN DOOR-ELECTRICAL SUPPLY UNIT (DRIVER’S SIDE) AND CONNECTOR C-22 FOR SHORT TO POWER SUPPLY
• Switch the ignition off.
• Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the connector C-22.
• Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at door-electrical supply unit (driver’s side) terminals 1A and 1B.
• Is the voltage between 1.5—3.5 V?
Yes
Repair or replace the wiring harness between connector C-47 and connector C-22 because the wiring harness is shorted to the power supply.
No
Go to the next step.
34
INSPECT DOOR-ELECTRICAL SUPPLY UNIT (DRIVER’S SIDE) FOR SHORT TO POWER SUPPLY
• Switch the ignition off.
• Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the door-electrical supply unit (driver’s side) connector.
• Connect the connector C-22.
• Connect the connector C-47.
• Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2L and 2J.
• Is the voltage between 1.5—3.5 V?
Yes
Replace the door-electrical supply unit (driver’s side) because there is a short to the power supply in the door-electrical supply unit (driver’s side).
No
Repair or replace the wiring harness between the door-electrical supply unit (driver’s side) and connector C-22 because the wiring harness is shorted to the power supply.
35
INSPECT ESU FOR SHORT TO POWER SUPPLY
• Switch the ignition off.
• Disconnect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Disconnect the ESU connector.
• Connect the connector C-47.
• Connect the negative battery terminal. (See NEGATIVE BATTERY TERMINAL DISCONNECTION/CONNECTION [(US)].)
• Switch the ignition ON (engine off).
• Measure the voltage at body control module (BCM) terminals 2L and 2J.
• Is the voltage between 1.5—3.5 V?
Yes
Replace the ESU because there is a short to the power supply in the ESU.
No
Repair or replace the wiring harness between the ESU and connector C-47 because the wiring harness is shorted to the power supply.