DTC P151B:00 [PCM (SKYACTIV-G (US))]
DTC P151B:00 [PCM (SKYACTIV-G (US))]
SM2565571
id0102t48893u0
Outline
System malfunction location |
IAC system problem |
||||
---|---|---|---|---|---|
Detection condition
|
• The PCM cannot control the idle speed toward the target idle speed during the KOER self test.
|
||||
Fail-safe
|
• Not applicable
|
||||
Possible cause
|
• A/C magnetic clutch malfunction
• Drive-by-wire control system malfunction
• Malfunction in injection amount measurement system (refer to DTC P0101:00)
• Purge solenoid valve malfunction
• Air cleaner element restricted
• Throttle body passage blockage
• Engine malfunction
• Generator control circuit malfunction
• PCM malfunction
|
||||
System wiring diagram
|
• Not applicable
|
||||
Connector diagram
|
• Not applicable
|
Diagnostic Procedure
Step |
Inspection |
Results |
Action |
---|---|---|---|
1
|
RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION
• Record the freeze frame data/snapshot data.
|
—
|
Go to the next step.
|
2
|
VERIFY RELATED REPAIR INFORMATION OR SERVICE INFORMATION AVAILABILITY
• Verify related Service Bulletins, on-line repair information, or Service Information availability.
• Is any related Information available?
|
Yes
|
Perform repair or diagnosis according to the available information.
• If the vehicle is not repaired, go to the next step.
|
No
|
Go to the next step.
|
||
3
|
INSPECT FOR OTHER RELATED DTCs
• Perform the DTC inspection for the PCM. (See DTC INSPECTION.)
• Are any other DTCs displayed?
|
Yes
|
Repair the malfunctioning location according to the applicable DTC troubleshooting.
|
No
|
Go to the next step.
|
||
4
|
INSPECT A/C MAGNETIC CLUTCH OPERATION
• Turn the A/C switch off.
• Is the magnetic clutch still on?
|
Yes
|
Perform the symptom troubleshooting “A/C IS ALWAYS ON OR A/C COMPRESSOR RUNS CONTINUOUSLY”.
|
No
|
Go to the next step.
|
||
5
|
INSPECT DRIVE-BY-WIRE CONTROL SYSTEM MALFUNCTION
• Perform the Drive-by-wire Control System Inspection. (See ENGINE CONTROL SYSTEM OPERATION INSPECTION [SKYACTIV-G (US)].)
• Is there any malfunction?
|
Yes
|
Repair or replace the malfunctioning location and perform the repair completion verification.
|
No
|
Go to the next step.
|
||
6
|
INSPECT PURGE SOLENOID VALVE
• Perform the Purge Control System Inspection. (See PURGE SOLENOID VALVE INSPECTION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))].) (See PURGE SOLENOID VALVE INSPECTION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))].)
• Is there any malfunction?
|
Yes
|
Repair or replace the malfunctioning location and perform the repair completion verification.
|
No
|
Go to the next step.
|
||
7
|
INSPECT AIR CLEANER ELEMENT FOR MALFUNCTION
• Remove the air cleaner element with the engine is running. (See AIR CLEANER ELEMENT REMOVAL/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))].) (See AIR CLEANER ELEMENT REMOVAL/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))].)
• Does the engine speed increase?
|
Yes
|
Clean or replace the air cleaner element and perform the repair completion verification.
|
No
|
Go to the next step.
|
||
8
|
INSPECT THROTTLE BODY PASSAGE
• Visually inspect the throttle body passage.
• Is the throttle body passage dirty and/or restricted?
|
Yes
|
Clean or replace the throttle body passage and perform the repair completion verification.
|
No
|
Go to the next step.
|
||
9
|
INSPECT ENGINE COMPRESSION
• Inspect the engine compression. (See COMPRESSION INSPECTION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))].) (See COMPRESSION INSPECTION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))].)
• Are compression pressures within specification?
|
Yes
|
Go to the next step.
|
No
|
Repair or replace the malfunctioning location and perform the repair completion verification.
|
||
10
|
INSPECT GENERATOR CONTROL CIRCUIT FOR SHORT TO POWER SUPPLY
• Apply the electrical load (such as blower fan, rear window defogger, or headlight).
• Does the engine speed increase?
|
Yes
|
Go to the next step.
|
No
|
Repair or replace the malfunctioning location and perform the repair completion verification.
|
||
Repair completion verification 1
|
VERIFY THAT VEHICLE IS REPAIRED
• Install/connect the part removed/disconnected during the troubleshooting procedure.
• Clear the DTC recorded in the memory. (See CLEARING DTC.)
• Replicate the vehicle conditions at the time the DTC was detected using the following procedure.
• Perform the DTC inspection for the PCM. (See DTC INSPECTION.)
• Is the same Pending DTC present?
|
Yes
|
Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.
If the CAN communication is normal, perform the diagnosis from Step 1.
• If the malfunction recurs, replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))].) (See PCM REMOVAL/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))].)
|
No
|
Go to the next step.
|
||
Repair completion verification 2
|
VERIFY IF OTHER DTCs DISPLAYED
• Perform the DTC inspection. (See DTC INSPECTION.)
• Are any other DTCs displayed?
|
Yes
|
Repair the malfunctioning location according to the applicable DTC troubleshooting.
|
No
|
DTC troubleshooting completed.
|