DTC P2226:00 [PCM (SKYACTIV-G)]
DTC P2226:00 [PCM (SKYACTIV-G)]
SM2334416
id0102t4159300
-
Note
-
• To determine the malfunctioning part, proceed with the diagnostics from “Function Inspection Using M-MDS”.
Details On DTCs
Description |
BARO sensor range/performance problem |
|
---|---|---|
Detection condition
|
Determination conditions
|
• Communication error between BARO sensor and PCM
• Non-volatile memory error in BARO sensor
|
Preconditions
|
• Battery voltage: 10.5—16 V *1
*1: Standard can be verified by displaying PIDs using M-MDS
|
|
Malfunction determination period
|
• 5 s period
|
|
Drive cycle
|
• 1
|
|
Self test type
|
• CMDTC self test, KOEO self test, KOER self test
|
|
Sensor used
|
• BARO sensor (built-into PCM)
|
|
Fail-safe function
|
• Fixes the barometric pressure for the engine control at 101.32 kPa {1.0332 kgf/cm2, 14.695 psi}.
|
|
Vehicle status when DTCs are output
|
• Not applicable
|
|
Possible cause
|
• BARO sensor (built-into PCM) malfunction
• PCM malfunction
|
System Wiring Diagram
Function Explanation (DTC Detection Outline)
Repeatability Verification Procedure
PID Item/Simulation Item Used In Diagnosis
Function Inspection Using M-MDS
Step |
Inspection |
Results |
Action |
---|---|---|---|
1
|
PURPOSE: VERIFY RELATED REPAIR INFORMATION OR SERVICE INFORMATION AVAILABILITY
• Verify related Service Bulletins, on-line repair information, or Service Information availability.
• Is any related Information available?
|
Yes
|
Perform repair or diagnosis according to the available information.
• If the vehicle is not repaired, go to the next step.
|
No
|
Go to the next step.
|
||
2
|
PURPOSE: RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION
• Record the freeze frame data/snapshot data.
|
—
|
Go to Troubleshooting Diagnostic Procedure to perform the procedure from Step 1.
|
Troubleshooting Diagnostic Procedure
-
― Perform a unit inspection of the BARO sensor.
-
― Verify that the primary malfunction is resolved and there are no other malfunctions.
Step |
Inspection |
Results |
Action |
---|---|---|---|
1
|
PURPOSE: INSPECT BARO SENSOR FOR MALFUNCTION
• Inspect the applicable part. (See BAROMETRIC PRESSURE (BARO) SENSOR INSPECTION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))].) (See BAROMETRIC PRESSURE (BARO) SENSOR INSPECTION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))].)
• Is the part normal?
|
Yes
|
Go to the next step.
|
No
|
Repair or replace the malfunctioning location and perform the repair completion verification.
|
||
Repair completion verification 1
|
PURPOSE: VERIFY THAT VEHICLE IS REPAIRED
• Install/connect the part removed/disconnected during the troubleshooting procedure.
• Clear the DTC recorded in the memory. (See CLEARING DTC.)
• Replicate the vehicle conditions at the time the DTC was detected using the following procedure.
• Perform the DTC inspection for the PCM. (See DTC INSPECTION.)
• Is the same Pending DTC present?
|
Yes
|
Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.
If the CAN communication is normal, perform the diagnosis from Step 1.
• If the malfunction recurs, replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [SKYACTIV-G (WITH CYLINDER DEACTIVATION (US))].) (See PCM REMOVAL/INSTALLATION [SKYACTIV-G (WITHOUT CYLINDER DEACTIVATION (US))].)
|
No
|
Go to the next step.
|
||
Repair completion verification 2
|
PURPOSE: VERIFY IF OTHER DTCs DISPLAYED
• Perform the DTC inspection. (See DTC INSPECTION.)
• Are any other DTCs displayed?
|
Yes
|
Repair the malfunctioning location according to the applicable DTC troubleshooting.
|
No
|
DTC troubleshooting completed.
|