PODS-F ECU
| 1. |
Disconnect the battery negative cable, and
wait for at least three minutes before beginning
work. |
| 2. |
Remove the front passenger seat assembly.
(Refer to the Body group -
"Seat") |
| 3. |
Disconnect the PODS-F ECU
connector. |
| 4. |
Remove the seat cushion cover assembly.
(Refer to the Body group -
"Seat") |
| 5. |
Remove the seat track assembly.
(Refer to the Body group -
"Seat")
|
PODS-F Mat
| 1. |
Disconnect the battery negative cable, and
wait for at least three minutes before beginning
work. |
| 2. |
Remove the front passenger seat assembly.
(Refer to the Body group -
"Seat") |
| 3. |
Disconnect the PODS-F mat
connector. |
| 4. |
Remove the seat cushion assembly.
(Refer to the Body group -
"Seat")
|
PODS-F ECU
| 1. |
Install the PODS-F ECU equipped seat track
assembly.
(Refer to the Body group -
"Seat") |
| 2. |
Install the seat cushion cover
assembly.
(Refer to the Body group -
"Seat") |
| 3. |
Connect the PODS-F ECU
connector. |
| 4. |
Install the front passenger seat assembly.
(Refer to the Body group -
"Seat") |
| 5. |
Reconnect the battery negative
cable. |
| 6. |
After installing the PODS-F, confirm proper
system operation :
| A. |
Turn the ignition switch ON the SRS
indicator should be turned on for about six seconds and then
go off. |
| B. |
Telltale lamp will turn on for 4 seconds
and be turned off for 3 seconds. After the 7 seconds, it shall
remain off if the PODS-F does not require suppression and the
passenger airbag is enabled. |
|
Be sure to perform PODS-F reset with GDS
after replcacing PODS-F equipped seat cushion.
| |
PODS-F Mat
| 1. |
Install the PODS-F Mat equipped seat cushion
assembly.
(Refer to the Body group -
"Seat") |
| 2. |
Install the front passenger seat assembly.
(Refer to the Body group -
"Seat") |
| 3. |
Connect the PODS-F mat
connector. |
| 4. |
Reconnect the battery negative
cable. |
| 5. |
After installing the PODS-F, confirm proper
system operation :
| A. |
Turn the ignition switch ON the SRS
indicator should be turned on for about six seconds and then
go off. |
| B. |
Telltale lamp will turn on for 4 seconds
and be turned off for 3 seconds. After the 7 seconds, it shall
remain off if the PODS-F does not require suppression and the
passenger airbag is enabled. |
|
Be sure to perform PODS-F zeroing with
GDS after replcacing PODS-F equipped seat
cushion. | |
You should perform
PODS-F Re-zero procedure after service or replacement about all part of
the passenger seat. (Not included full seat assembly)
| 1. |
Ignition “OFF”, connect
GDS. |
| 2. |
Ignition “ON” & Engine “OFF”, select
Airbag system and “PODS-F Reset” mode.
|
| 3. |
The GDS will show the two PODS-F Zeroing
function steps.
| (1) |
Erase PODS-F diagnostic
codes. |
| (2) |
PODS-F initialization.
|
This step must be done PODS-F
re-zero, when the front passenger seat is
empty. | | |
| 4. |
The PODS-F initialization procedure will be
performed.
|
Erase the SRSCM diagnostic codes after
completing the PODS-F
zeroing. |
|
In case of zeroing failure
| -
|
Code 01 : Requestor ID out of
range. |
| -
|
Code 03 : ODS sensor short to
ground. |
| -
|
Code 04 : Open between ODS ECU and
mat. |
| -
|
Code 05 : ODS ECU has not been
trimmed. |
| -
|
Code 06 : Configuration disabled
in ECU calibration. |
| -
|
Code 07 : Configuration value out
of range. |
| -
|
Code 08 : Used in zero Request
response only. |
| -
|
Code 09 : Algo enabled this
ignition cycles. |
| -
|
Code 0A : Upper offset value
created during the zero
process. |
| -
|
Code 0B : Lower offset value
created during the zero
process. |
| -
|
Code 0C : Voltage
diagnostic |
| -
|
Code 0D : The delta of QX_Freq_Low
and QX_Freq_High must remain
low. |
| -
|
Code 0E : Temperature is above O
deg C during the zero
process. |
| -
|
Code 0F : Re-read QX Final compare
delta limit. (zero
verify) | | |
