{"id":9771,"date":"2017-06-11T23:57:32","date_gmt":"2017-06-11T23:57:32","guid":{"rendered":"http:\/\/mazdaman.x10host.com\/sm353444\/"},"modified":"2017-06-11T23:57:32","modified_gmt":"2017-06-11T23:57:32","slug":"sm353444","status":"publish","type":"page","link":"https:\/\/www.hexorcism.com\/16ND\/sm353444\/","title":{"rendered":"DTC B00A0:28 [SAS CONTROL MODULE (TWO-STEP DEPLOYMENT CONTROL SYSTEM)]"},"content":{"rendered":"
\n <\/p>\n
\n
\n
\n < Previous<\/a> Next ><\/a><\/p>\n

2016 – MX-5 – Restraints<\/h2>\n

<\/a><\/p>\n

DTC B00A0:28 [SAS CONTROL MODULE (TWO-STEP DEPLOYMENT CONTROL SYSTEM)]<\/h3>\n\n\n\n\n\n\n\n
\n

System malfunction location<\/b><\/p>\n<\/td>\n

\n
    \n
  • \n

    Occupant classification sensor calibration setting invalid<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<\/tr>\n

\n

Detection condition<\/b><\/p>\n<\/td>\n

\n

WARNING:<\/span><\/b><\/p>\n

    \n
  • \n

    Detection conditions are for understanding the DTC outline before performing an inspection. Performing an inspection according to only the detection conditions may cause injury due to an operating error, or damage the system. When performing an inspection, always follow the inspection procedure.<\/p>\n<\/li>\n<\/ul>\n

      \n
    • \n

      Calibration set value not within valid range.<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<\/tr>\n

\n

Fail-safe<\/b><\/p>\n<\/td>\n

\n

\u2014<\/p>\n<\/td>\n<\/tr>\n

\n

Possible cause<\/b><\/p>\n<\/td>\n

\n
    \n
  • \n

    Occupant classification sensor deformed or malfunction<\/p>\n<\/li>\n

  • \n

    Object placed on front passenger-side seat during calibration of occupant classification sensor<\/p>\n<\/li>\n

  • \n

    Improperly installed front passenger-side seat part at time of calibration<\/p>\n<\/li>\n

  • \n

    Deformed floor where attached to front passenger-side seat<\/p>\n<\/li>\n

  • \n

    Seat warmer is dry malfunction<\/p>\n<\/li>\n

  • \n

    Seat cushion is damp<\/p>\n<\/li>\n

  • \n

    Occupant classification sensor malfunction<\/p>\n<\/li>\n

  • \n

    SAS control module malfunction<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<\/tr>\n

\n

System wiring diagram<\/b><\/p>\n<\/td>\n

\n

\u2014<\/p>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

\n <\/a><\/p>\n

Diagnostic Procedure<\/h4>\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
\n

Step<\/p>\n<\/td>\n

\n

Inspection<\/p>\n<\/td>\n

\n

Action<\/p>\n<\/td>\n<\/tr>\n

\n

1<\/p>\n<\/td>\n

\n PERFORM SAS CONTROL MODULE CONFIGURATION (AS-BUILT DATA USE)<\/b><\/p>\n\n

Yes<\/p>\n<\/td>\n

\n

Go to the next step.<\/p>\n<\/td>\n<\/tr>\n

\n

No<\/p>\n<\/td>\n

\n

DTC troubleshooting completed.<\/p>\n<\/td>\n<\/tr>\n

\n

2<\/p>\n<\/td>\n

\n INSPECT SEAT CUSHION<\/b><\/p>\n
    \n
  • \n

    Inspect the seat cushion.<\/p>\n<\/li>\n

  • \n

    Is the seat cushion damp?<\/p>\n<\/li>\n<\/ul>\n<\/td>\n

\n

Yes<\/p>\n<\/td>\n

\n

Seat cushion is dry.<\/p>\n

Perform the DTC inspection again. If the same DTC is displayed, go to the next step.<\/p>\n<\/td>\n<\/tr>\n

\n

No<\/p>\n<\/td>\n

\n

Go to the next step.<\/p>\n<\/td>\n<\/tr>\n

\n

3<\/p>\n<\/td>\n

\n INSPECT SEAT WARMER<\/b><\/p>\n\n

Yes<\/p>\n<\/td>\n

\n

Go to the next step.<\/p>\n<\/td>\n<\/tr>\n

\n

No<\/p>\n<\/td>\n

\n

Replace the seat warmer. (See SEAT BACK TRIM REMOVAL\/INSTALLATION<\/a>.)(See SEAT CUSHION TRIM REMOVAL\/INSTALLATION<\/a>.)<\/p>\n

\n

4<\/p>\n<\/td>\n

\n INSPECT PASSENGER-SIDE SEAT<\/b><\/p>\n\n

Yes<\/p>\n<\/td>\n

\n

Replace the seat warmer. (See SEAT BACK TRIM REMOVAL\/INSTALLATION<\/a>.)(See SEAT CUSHION TRIM REMOVAL\/INSTALLATION<\/a>.)<\/p>\n

\n

No<\/p>\n<\/td>\n

\n

Go to the next step.<\/p>\n<\/td>\n<\/tr>\n

\n

5<\/p>\n<\/td>\n

\n INSPECT FLOOR<\/b><\/p>\n
    \n
  • \n

    Visually inspect the installation parts of the front passenger-side seat for the following:<\/p>\n<\/li>\n

      \n
    • \n

      Abnormal floor deformation<\/p>\n<\/li>\n

    • \n

      Installation hole of front passenger-side seat is improperly positioned<\/p>\n<\/li>\n<\/ul>\n

    • \n

      Is the floor normal?<\/p>\n<\/li>\n<\/ul>\n<\/td>\n

\n

Yes<\/p>\n<\/td>\n

\n

Go to the next step.<\/p>\n<\/td>\n<\/tr>\n

\n

No<\/p>\n<\/td>\n

\n

Repair floor deformation.<\/p>\n

\n

6<\/p>\n<\/td>\n

\n INSPECT OCCUPANT CLASSIFICATION SENSOR<\/b><\/p>\n\n

Yes<\/p>\n<\/td>\n

\n

Replace the occupant classification sensor. (See OCCUPANT CLASSIFICATION SENSOR REMOVAL\/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM]<\/a>.)<\/p>\n

\n

No<\/p>\n<\/td>\n

\n

DTC troubleshooting completed.<\/p>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

\n < Previous<\/a> Next ><\/a><\/p>\n

\n Back to Top<\/a>\n <\/div>\n
\n \u00a9 2014 Mazda North American Operations, U.S.A.<\/em>\n <\/div>\n<\/p><\/div>\n<\/p><\/div>\n<\/p><\/div>\n<\/p><\/div>\n","protected":false},"excerpt":{"rendered":"

< Previous Next > 2016 – MX-5 – Restraints DTC B00A0:28 [SAS CONTROL MODULE (TWO-STEP DEPLOYMENT CONTROL SYSTEM)] System malfunction location Occupant classification sensor calibration setting invalid Detection condition WARNING: Detection conditions are for understanding the DTC outline before performing an inspection. Performing an inspection according to only the detection conditions may cause injury due to an operating error, or damage the system. When performing an inspection, always follow the inspection procedure. Calibration set value […]<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_monsterinsights_skip_tracking":false,"_monsterinsights_sitenote_active":false,"_monsterinsights_sitenote_note":"","_monsterinsights_sitenote_category":0,"footnotes":""},"class_list":["post-9771","page","type-page","status-publish","hentry"],"_links":{"self":[{"href":"https:\/\/www.hexorcism.com\/16ND\/wp-json\/wp\/v2\/pages\/9771","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.hexorcism.com\/16ND\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/www.hexorcism.com\/16ND\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/16ND\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/16ND\/wp-json\/wp\/v2\/comments?post=9771"}],"version-history":[{"count":0,"href":"https:\/\/www.hexorcism.com\/16ND\/wp-json\/wp\/v2\/pages\/9771\/revisions"}],"wp:attachment":[{"href":"https:\/\/www.hexorcism.com\/16ND\/wp-json\/wp\/v2\/media?parent=9771"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}