{"id":9751,"date":"2017-06-11T23:57:34","date_gmt":"2017-06-11T23:57:34","guid":{"rendered":"http:\/\/mazdaman.x10host.com\/sm353424\/"},"modified":"2017-06-11T23:57:34","modified_gmt":"2017-06-11T23:57:34","slug":"sm353424","status":"publish","type":"page","link":"https:\/\/www.hexorcism.com\/16ND\/sm353424\/","title":{"rendered":"DTC B0001:11\/B0001:12\/B0001:13\/B0001:19\/B0001:1A [SAS CONTROL MODULE (TWO-STEP DEPLOYMENT CONTROL SYSTEM)]"},"content":{"rendered":"
\n <\/p>\n
\n
\n
\n < Previous<\/a> Next ><\/a><\/p>\n

2016 – MX-5 – Restraints<\/h2>\n

<\/a><\/p>\n

DTC B0001:11\/B0001:12\/B0001:13\/B0001:19\/B0001:1A [SAS CONTROL MODULE (TWO-STEP DEPLOYMENT CONTROL SYSTEM)]<\/h3>\n\n\n\n\n\n\n\n
\n

System malfunction location<\/p>\n<\/td>\n

\n
    \n
  • \n

    B0001:11: Driver-side air bag module (inflator No.1) circuit short to body ground<\/p>\n<\/li>\n

  • \n

    B0001:12: Driver-side air bag module (inflator No.1) circuit short to power supply<\/p>\n<\/li>\n

  • \n

    B0001:13: Driver-side air bag module (inflator No.1) circuit open circuit or resistance high<\/p>\n<\/li>\n

  • \n

    B0001:19: Short circuit to driver-side air bag module (inflator no.1) and other air bag module circuits<\/p>\n<\/li>\n

  • \n

    B0001:1A: Driver-side air bag module (inflator No.1) circuit resistance low<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<\/tr>\n

\n

Detection condition<\/b><\/p>\n<\/td>\n

\n

WARNING:<\/span><\/b><\/p>\n

    \n
  • \n

    Detection conditions are for understanding the DTC outline before performing an inspection. Performing an inspection according to only the detection conditions may cause injury due to an operating error, or damage the system. When performing an inspection, always follow the inspection procedure.<\/p>\n<\/li>\n<\/ul>\n

      \n
    • \n

      Resistance other than 1.37\u20136.33 ohms<\/b> detected in driver-side air bag module (inflator no.1) circuit<\/p>\n<\/li>\n

    • \n

      Wiring harness between driver-side air bag module (inflator no.1) and SAS control module has malfunction<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<\/tr>\n

\n

Fail-safe function<\/b><\/p>\n<\/td>\n

\n

Not applicable<\/p>\n<\/td>\n<\/tr>\n

\n

Possible cause<\/b><\/p>\n<\/td>\n

\n
    \n
  • \n

    Clock spring connector malfunction<\/p>\n<\/li>\n

  • \n

    Clock spring malfunction<\/p>\n<\/li>\n

  • \n

    Short circuit to power supply or body ground in the wiring harness between the clock spring and SAS control module<\/p>\n<\/li>\n

  • \n

    Open circuit in the wiring harness between the clock spring and SAS control module<\/p>\n<\/li>\n

  • \n

    Driver-side air bag module (inflator No.1) malfunction<\/p>\n<\/li>\n

  • \n

    SAS control module malfunction<\/p>\n<\/li>\n<\/ul>\n<\/td>\n<\/tr>\n

\n

<\/a><\/p>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

\n <\/a><\/p>\n

Diagnostic Procedure<\/h4>\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
\n

Step<\/p>\n<\/td>\n

\n

Inspection<\/p>\n<\/td>\n

\n

Action<\/p>\n<\/td>\n<\/tr>\n

\n

1<\/p>\n<\/td>\n

\n INSPECT DRIVER-SIDE AIR BAG MODULE (INFLATOR NO.1) CONNECTOR<\/b><\/p>\n

WARNING:<\/span><\/b><\/p>\n

\n

Yes<\/p>\n<\/td>\n

\n

Replace clock spring.<\/p>\n

(See CLOCK SPRING REMOVAL\/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM]<\/a>.)<\/p>\n

Then go to Step 7.<\/p>\n<\/td>\n<\/tr>\n

\n

No<\/p>\n<\/td>\n

\n

Go to the next step.<\/p>\n<\/td>\n<\/tr>\n

\n

2<\/p>\n<\/td>\n

\n INSPECT CLOCK SPRING<\/b><\/p>\n\n

Yes<\/p>\n<\/td>\n

\n

Go to the next step.<\/p>\n<\/td>\n<\/tr>\n

\n

No<\/p>\n<\/td>\n

\n

Replace clock spring.<\/p>\n

(See CLOCK SPRING REMOVAL\/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM]<\/a>.)<\/p>\n

Then go to Step 7.<\/p>\n<\/td>\n<\/tr>\n

\n

3<\/p>\n<\/td>\n

\n INSPECT DRIVER-SIDE AIR BAG MODULE (INFLATOR NO.1) CIRCUIT FOR SHORT TO GROUND<\/b><\/p>\n\n

Yes<\/p>\n<\/td>\n

\n

Refer to the wiring diagram and verify whether or not there is a common connector between SAS control module terminal and clock spring terminal.<\/p>\n

    \n If there is a common connector:<\/b><\/p>\n
  • \n

    Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground.<\/p>\n<\/li>\n

  • \n

    Replace the malfunctioning part.<\/p>\n<\/li>\n<\/ul>\n

      \n If there is no common connector:<\/b><\/p>\n
    • \n

      Replace the wiring harness which has a short to ground.<\/p>\n<\/li>\n<\/ul>\n

      Go to Step 7.<\/p>\n<\/td>\n<\/tr>\n

\n

No<\/p>\n<\/td>\n

\n

Go to the next step.<\/p>\n<\/td>\n<\/tr>\n

\n

4<\/p>\n<\/td>\n

\n INSPECT DRIVER-SIDE AIR BAG MODULE (INFLATOR NO.1) CIRCUIT FOR OPEN CIRCUIT<\/b><\/p>\n
    \n
  • \n

    SAS control module and clock spring connectors are disconnected.<\/p>\n<\/li>\n

  • \n

    Inspect for continuity between the following terminals (wiring harness-side):<\/p>\n<\/li>\n

      \n
    • \n

      Clock spring terminal 2B\u2014SAS control module terminal 3C<\/p>\n<\/li>\n

    • \n

      Clock spring terminal 2A\u2014SAS control module terminal 3G<\/p>\n<\/li>\n<\/ul>\n<\/ul>\n

      NOTE:<\/span><\/b><\/p>\n

        \n
      • \n

        Inspect for continuity while shaking the wiring harness between the SAS control module and clock spring.<\/p>\n<\/li>\n<\/ul>\n

          \n
        • \n

          Is there continuity?<\/p>\n<\/li>\n<\/ul>\n<\/td>\n

\n

Yes<\/p>\n<\/td>\n

\n

Go to the next step.<\/p>\n<\/td>\n<\/tr>\n

\n

No<\/p>\n<\/td>\n

\n

Refer to the wiring diagram and verify whether or not there is a common connector between SAS control module terminal and clock spring terminal.<\/p>\n

    \n If there is a common connector:<\/b><\/p>\n
  • \n

    Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.<\/p>\n<\/li>\n

  • \n

    Replace the malfunctioning part.<\/p>\n<\/li>\n<\/ul>\n

      \n If there is no common connector:<\/b><\/p>\n
    • \n

      Replace the wiring harness which has an open circuit.<\/p>\n<\/li>\n<\/ul>\n

      Go to Step 7.<\/p>\n<\/td>\n<\/tr>\n

\n

5<\/p>\n<\/td>\n

\n INSPECT DRIVER-SIDE AIR BAG MODULE (INFLATOR NO.1) CIRCUIT FOR SHORT TO POWER SUPPLY<\/b><\/p>\n\n

Yes<\/p>\n<\/td>\n

\n

Go to the next step.<\/p>\n<\/td>\n<\/tr>\n

\n

No<\/p>\n<\/td>\n

\n

Refer to the wiring diagram and verify whether or not there is a common connector between SAS control module terminal and clock spring terminal.<\/p>\n

    \n If there is a common connector:<\/b><\/p>\n
  • \n

    Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to power supply.<\/p>\n<\/li>\n

  • \n

    Replace the malfunctioning part.<\/p>\n<\/li>\n<\/ul>\n

      \n If there is no common connector:<\/b><\/p>\n
    • \n

      Replace the wiring harness which has a short to power supply.<\/p>\n<\/li>\n<\/ul>\n

      Go to Step 7.<\/p>\n<\/td>\n<\/tr>\n

\n

6<\/p>\n<\/td>\n

\n INSPECT DRIVER-SIDE AIR BAG MODULE (INFLATOR NO.1)<\/b><\/p>\n\n

Yes<\/p>\n<\/td>\n

\n

Go to the next step.<\/p>\n<\/td>\n<\/tr>\n

\n

No<\/p>\n<\/td>\n

\n

Replace the driver-side air bag module (inflator no.1).<\/p>\n

(See DRIVER-SIDE AIR BAG MODULE REMOVAL [TWO-STEP DEPLOYMENT CONTROL SYSTEM]<\/a>.)<\/p>\n

(See DRIVER-SIDE AIR BAG MODULE INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM]<\/a>.)<\/p>\n

Then go to the next step.<\/p>\n<\/td>\n<\/tr>\n

\n

7<\/p>\n<\/td>\n

\n PERFORM SAS CONTROL MODULE DTC INSPECTION<\/b><\/p>\n\n

Yes<\/p>\n<\/td>\n

\n

Repeat the inspection from Step 1.<\/p>\n

\n

No<\/p>\n<\/td>\n

\n

DTC troubleshooting completed.<\/p>\n<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

\n < Previous<\/a> Next ><\/a><\/p>\n

\n Back to Top<\/a>\n <\/div>\n
\n \u00a9 2014 Mazda North American Operations, U.S.A.<\/em>\n <\/div>\n<\/p><\/div>\n<\/p><\/div>\n<\/p><\/div>\n<\/p><\/div>\n","protected":false},"excerpt":{"rendered":"

< Previous Next > 2016 – MX-5 – Restraints DTC B0001:11\/B0001:12\/B0001:13\/B0001:19\/B0001:1A [SAS CONTROL MODULE (TWO-STEP DEPLOYMENT CONTROL SYSTEM)] System malfunction location B0001:11: Driver-side air bag module (inflator No.1) circuit short to body ground B0001:12: Driver-side air bag module (inflator No.1) circuit short to power supply B0001:13: Driver-side air bag module (inflator No.1) circuit open circuit or resistance high B0001:19: Short circuit to driver-side air bag module (inflator no.1) and other air bag module circuits B0001:1A: […]<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_monsterinsights_skip_tracking":false,"_monsterinsights_sitenote_active":false,"_monsterinsights_sitenote_note":"","_monsterinsights_sitenote_category":0,"footnotes":""},"class_list":["post-9751","page","type-page","status-publish","hentry"],"_links":{"self":[{"href":"https:\/\/www.hexorcism.com\/16ND\/wp-json\/wp\/v2\/pages\/9751","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.hexorcism.com\/16ND\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/www.hexorcism.com\/16ND\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/16ND\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.hexorcism.com\/16ND\/wp-json\/wp\/v2\/comments?post=9751"}],"version-history":[{"count":0,"href":"https:\/\/www.hexorcism.com\/16ND\/wp-json\/wp\/v2\/pages\/9751\/revisions"}],"wp:attachment":[{"href":"https:\/\/www.hexorcism.com\/16ND\/wp-json\/wp\/v2\/media?parent=9751"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}