Description

Audio amplifier low power supply voltage input

Detection condition

• Audio amplifier power supply circuit voltage of 9.0 ±0.8 V or less is detected for 5 s or more with the ignition switched ON (engine off or on).

Fail-safe

Not applicable

Possible cause

• DTCs are stored in the PCM.

• Battery malfunction

• Generator malfunction

• Audio amplifier connector or terminal malfunction

• Audio amplifier power supply circuit malfunction

• Short to ground in the wiring harness between MAIN 200 A fuse and audio amplifier terminal 3A

• AUDIO1 25 A fuse malfunction

• CABIN+B 50 A fuse malfunction

• MAIN 200 A fuse malfunction

• Open circuit in wiring harness between battery positive terminal and audio amplifier terminal 3A

• Audio amplifier malfunction

Step

Inspection

Action

1

• Retrieve the PCM DTCs using the M-MDS.

  (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.0)].)

• Are any DTCs displayed?

Yes

Repair or replace the malfunctioning part according to the applicable DTC troubleshooting.

(See DTC TABLE [PCM (SKYACTIV-G 2.0)].)

No

Go to the next step.

2

• Inspect the battery.

  (See BATTERY INSPECTION.)

• Is the battery normal?

Yes

Go to the next step.

No

Recharge or replace the battery, then go to Step 6.

(See BATTERY RECHARGING.)

(See BATTERY REMOVAL/INSTALLATION [SKYACTIV-G 2.0].)

3

• Inspect the generator.

  (See GENERATOR INSPECTION [SKYACTIV-G 2.0].)

• Is the generator normal?

Yes

Go to the next step.

No

Replace the generator, then go to Step 6.

(See GENERATOR REMOVAL/INSTALLATION [SKYACTIV-G 2.0].)

4

• Switch the ignition off.

• Disconnect the negative battery cable.

  (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION.)

• Disconnect the audio amplifier connector.

• Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection.

• Is the connector normal?

Yes

Go to the next step.

No

Repair or replace the connector, then go to Step 6.

5

• Verify that the audio amplifier connector is disconnected.

• Connect the negative battery cable.

  (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION.)

• Switch the ignition ON (engine off or on).

• Measure the voltage at audio amplifier terminal 3A (wiring harness-side).

• Is the voltage B+?

Yes

Go to the next step.

No

Inspect the AUDIO1 25 A fuse, CABIN+B 50 A fuse, and MAIN 200 A fuse.

• Any fuse is blown:

• Refer to the wiring diagram and verify if there is a common connector between MAIN 200 A fuse and audio amplifier 3A.

If there is a common connector:

• Inspect the common connector and terminals for corrosion, damage, or disconnection and the common wiring harnesses for short to ground to determine the malfunctioning location.

• Repair or replace the malfunctioning location.

If there is no common connector:

• Repair or replace the wiring harness which is shorted to ground.

• Replace the fuse.

• Any fuse is damaged:

• Replace the fuse.

• All fuses are normal:

• Refer to the wiring diagram and verify if there is a common connector between battery positive terminal and audio amplifier terminal 3A.

If there is a common connector:

• Inspect the common connector and terminals for corrosion, damage, or disconnection and the common wiring harnesses for an open circuit to determine the malfunctioning location.

• Repair or replace the malfunctioning location.

If there is no common connector:

• Repair or replace the wiring harness which has an open circuit.

Go to the next step.

6

• Always reconnect all disconnected connectors.

• Connect the negative battery cable.

  (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION.)

• Clear the DTC for the audio amplifier using the M-MDS.

  (See CLEARING DTC [AUDIO AMPLIFIER].)

• Switch the ignition ON (engine off or on) and wait for 5 s or more.

• Retrieve the audio amplifier DTCs using the M-MDS.

  (See DTC INSPECTION [AUDIO AMPLIFIER].)

• Is the same DTC displayed?

Yes

Repeat the inspection from Step 1.

• If the malfunction recurs, replace the audio amplifier.

  (See AUDIO AMPLIFIER REMOVAL/INSTALLATION.)

Go to the next step.

No

Go to the next step.

7

• Are any other DTCs displayed?

Yes

Repair or replace the malfunctioning part according to the applicable DTC troubleshooting.

(See DTC TABLE [AUDIO AMPLIFIER].)

No

DTC troubleshooting completed.