DTC P0073:00

Ambient temperature sensor circuit high input

DETECTION CONDITION

• The PCM monitors the input signal from the ambient temperature sensor. If the voltage from the ambient temperature sensor is above 4.88 V, the PCM determines that the ambient temperature sensor circuit has a malfunction.

Diagnostic support note

• This is a continuous monitor (other).

• The check engine light does not illuminate.

• FREEZE FRAME DATA is not available.

• Snapshot data is available.

• DTC is stored in the PCM memory.

FAIL-SAFE FUNCTION

Not applicable

POSSIBLE CAUSE

• Ambient temperature sensor connector or terminals malfunction

• PCM connector or terminals malfunction

• Short to power supply in wiring harness between ambient temperature sensor terminal A and PCM terminal 2I

• Open circuit in wiring harness between the following terminals:

• Ambient temperature sensor terminal A—PCM terminal 2I

• Ambient temperature sensor terminal B—PCM terminal 2AJ

• Ambient temperature sensor malfunction

• PCM malfunction

STEP

INSPECTION

ACTION

1

NOTE:

• Recording can be facilitated using the screen capture function of the PC.

• Record the snapshot data on the repair order.

—

Go to the next step.

2

• Verify related Service Bulletins and/or on-line repair information availability.

• Is any related repair information available?

Yes

Perform repair or diagnosis according to the available repair information.

• If the vehicle is not repaired, go to the next step.

No

Go to the next step.

3

• Switch the ignition off.

• Disconnect the ambient temperature sensor connector.

• Inspect for poor connection (such as damaged/pulled-out pins, corrosion).

• Is there any malfunction?

Yes

Repair or replace the connector and/or terminals, then go to Step 8.

No

Go to the next step.

4

• Disconnect the PCM connector.

• Inspect for poor connection (such as damaged/pulled-out pins, corrosion).

• Is there any malfunction?

Yes

Repair or replace the connector and/or terminals, then go to Step 8.

No

Go to the next step.

5

• Verify that the ambient temperature sensor and PCM connectors are disconnected.

• Switch the ignition ON (engine off).

  NOTE:

  • Another DTC may be stored by the PCM detecting an open circuit.

• Measure the voltage at the ambient temperature sensor terminal A (wiring harness-side).

• Is the voltage 0 V?

Yes

Go to the next step.

No

Refer to the wiring diagram and verify whether or not there is a common connector between ambient temperature sensor terminal A and PCM terminal 2I.

If there is a common connector:

• Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to power supply.

• Repair or replace the malfunctioning part.

If there is no common connector:

• Repair or replace the wiring harness which has a short to power supply.

Go to Step 8.

6

• Verify that the ambient temperature sensor and PCM connectors are disconnected.

• Switch the ignition off.

• Inspect for continuity between the following terminals (wiring harness-side):

• Ambient temperature sensor terminal A—PCM terminal 2I

• Ambient temperature sensor terminal B—PCM terminal 2AJ

• Is there continuity?

Yes

Go to the next step.

No

Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:

• Ambient temperature sensor terminal A—PCM terminal 2I

• Ambient temperature sensor terminal B—PCM terminal 2AJ

If there is a common connector:

• Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.

• Repair or replace the malfunctioning part.

If there is no common connector:

• Repair or replace the wiring harness which has an open circuit.

Go to Step 8.

7

• Inspect the ambient temperature sensor.

  (See AMBIENT TEMPERATURE SENSOR INSPECTION [MANUAL AIR CONDITIONER].)

  (See AMBIENT TEMPERATURE SENSOR INSPECTION [FULL-AUTO AIR CONDITIONER].)

• Is there any malfunction?

Yes

Replace the ambient temperature sensor, then go to the next step.

(See AMBIENT TEMPERATURE SENSOR REMOVAL/INSTALLATION [MANUAL AIR CONDITIONER].)

(See AMBIENT TEMPERATURE SENSOR REMOVAL/INSTALLATION [FULL-AUTO AIR CONDITIONER].)

No

Go to the next step.

8

• Always reconnect all disconnected connectors.

• Clear the DTC from the PCM memory using the M-MDS.

  (See AFTER REPAIR PROCEDURE [PCM (SKYACTIV-G 2.0)].)

• Perform the KOEO or KOER self test.

  (See KOEO/KOER SELF TEST [PCM (SKYACTIV-G 2.0)].)

• Is the same DTC present?

Yes

Repeat the inspection from Step 1.

• If the malfunction recurs, replace the PCM.

  (See PCM REMOVAL/INSTALLATION [SKYACTIV-G 2.0].)

Go to the next step.

No

Go to the next step.

9

• Perform the “AFTER REPAIR PROCEDURE”.

  (See AFTER REPAIR PROCEDURE [PCM (SKYACTIV-G 2.0)].)

• Are any DTCs present?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE [PCM (SKYACTIV-G 2.0)].)

No

DTC troubleshooting completed.